Experimental and Numerical Studies on Spherical Roller Bearings Using Multivariable Regression Analysis

Many industries make wide use of rotor bearing systems such as high speed turbines and generators. However, the vibration of antifriction rotor–bearings is a key factor in reducing the life of the bearings; thus significantly influencing the performance and working life of the whole power plant. In earlier research on the vibration characteristics of high speed rotor–bearing systems, such as in induced draft (ID) fans, an application used in sugar cane factories, the supporting antifriction bearings were simplified as a particle on a shaft with radial stiffness and damping coefficient. However, such simplification neglects the effects of the bearing structure on the vibration performance of the rotor–bearing system. This paper demonstrates the benefits of a more holistic approach and establishes a numerical model of the stiffness of the spherical roller bearing through Buckingham's π theorem (BPT). On the basis of this model, we argue for the benefits of a new dimensional analysis (DA) technique for rotor–bearing systems. Our new DA also considers the influences of the bearing structure parameters on the vibration of rotor–bearing systems. We demonstrate the effectiveness of our approach by conducting a comparative BPT study using an ID fan, a rotor–bearing system in use in sugar cane factories. We first analyzed an ID fan using the simplified model to obtain the defect frequencies and vibration amplitude responses of the ID fan system. Subsequently the same ID fan rotor was also analyzed using our new multivariable regression analysis (MVRA) approach to verify the validity of our new and holistic BPT. The results indicate that the new method we propose in this paper for the calculation of vibration characteristics of a high speed rotor–bearing (ID fan) is credible and will save time and costs by the accurate detection of imminent bearing failure.

[1]  R. G. Desavale,et al.  Antifriction Bearings Damage Analysis Using Experimental Data Based Models , 2013 .

[2]  T. A. Harris,et al.  Rolling Bearing Analysis , 1967 .

[3]  Nicolò Bachschmid,et al.  Identification of multiple faults in rotor systems , 2002 .

[4]  Maurice Adams,et al.  Rotating Machinery Vibration: From Analysis to Troubleshooting , 2000 .

[5]  P. D. McFadden,et al.  Model for the vibration produced by a single point defect in a rolling element bearing , 1984 .

[6]  P. D. McFadden,et al.  The vibration produced by multiple point defects in a rolling element bearing , 1985 .

[7]  Satish C. Sharma,et al.  Fault diagnosis of ball bearings using machine learning methods , 2011, Expert Syst. Appl..

[8]  N. Tandon,et al.  A review of vibration and acoustic measurement methods for the detection of defects in rolling element bearings , 1999 .

[9]  Jose Mathew,et al.  A theoretical model to predict the effect of localized defect on vibrations associated with ball bearing , 2010 .

[10]  H. Karagülle,et al.  Vibration analysis of rolling element bearings with various defects under the action of an unbalanced force , 2006 .

[11]  S. P. Harsha,et al.  Nonlinear Vibration Signature Analysis of High Speed Rotor Due to Defects of Rolling Element , 2008 .

[12]  Teresa Orlowska-Kowalska,et al.  Neural networks application for induction motor faults diagnosis , 2003, Math. Comput. Simul..

[13]  N. Tandon,et al.  A comparison of some condition monitoring techniques for the detection of defect in induction motor ball bearings , 2007 .

[14]  H. Langhaar.  Dimensional analysis and theory of models , 1951 .

[15]  A. J. Hoffman,et al.  The application of neural networks to vibrational diagnostics for multiple fault conditions , 2002, Comput. Stand. Interfaces.

[16]  Nizami Aktürk,et al.  An Investigation of Rolling Element Vibrations Caused by Local Defects , 2008 .

[17]  V. N. Patel,et al.  A Dynamic Model for Vibration Studies of Deep Groove Ball Bearings Considering Single and Multiple Defects in Races , 2010 .

[18]  Aleksandar Miltenović,et al.  Vibration response of rigid rotor in unloaded rolling element bearing , 2010 .

[19]  Homer Rahnejat,et al.  The Vibrations of Radial Ball Bearings , 1985 .

[20]  J. S. Rao,et al.  Vibratory Condition Monitoring of Machines , 2000 .

[21]  P. K. Kankar,et al.  Stability analysis of a rotor bearing system due to surface waviness and number of balls , 2004 .

[22]  Minel J. Braun,et al.  Vibration Monitoring and Damage Quantification of Faulty Ball Bearings , 2005 .