A novel method for the determination of the change in blade tip timing probe sensing position due to steady movements

Abstract The correlation of blade tip timing (BTT) measurements against strain gauge (SG) measurements and finite element (FE) predictions includes a number of uncertainties. One of the main ones is the steady movement of the blades (i.e. change in their mean position and orientation). This causes the sensing positions of the probes relative to a blade tip to deviate from their intended (nominal) positions, leading to deceptive results for the BTT amplitude and the corresponding stress levels. Such movements are caused by variations in static loading conditions (thermal and pressure) associated with changes in the operating speed. A novel method is introduced for the determination of three basic types of blade tip steady movements: axial; lean; untwist. The method relies on linking the shift in the averages of the BTT data to a number of geometrical relations, depending on the type of movement. Not more than two probes (to be placed at different axial positions) are needed to measure all three types of movement. The method is validated by simulations using a novel BTT simulator, and by measurements from both a test rig and real engine tests. The validated results demonstrate the great potential of the method for practical applications.

[1]  P. S. Heyns,et al.  A Comparison Between Three Blade Tip Timing Algorithms for Estimating Synchronous Turbomachine Blade Vibration , 2015 .

[2]  Jan R. Wright,et al.  BLADE-TIP TIMING MEASUREMENT OF SYNCHRONOUS VIBRATIONS OF ROTATING BLADED ASSEMBLIES , 2002 .

[3]  Grigorios Dimitriadis,et al.  A comparison of blade tip timing data analysis methods , 2001 .

[4]  Jan R. Wright,et al.  Development of a Multiple Modes Simulator of Rotating Bladed Assemblies for Blade Tip-Timing Data Analysis , 2002 .

[5]  Jan R. Wright,et al.  A class of methods for the analysis of blade tip timing data from bladed assemblies undergoing simultaneous resonances - Part II: Experimental validation , 2007 .

[6]  A. Savitzky,et al.  Smoothing and Differentiation of Data by Simplified Least Squares Procedures. , 1964 .

[7]  Jaromir Strnad,et al.  Diagnostic methods of a bladed disc mode shape evaluation used for shrouded blades in steam turbines , 2015 .

[8]  Craig Lawson,et al.  Compressor Blade Tip Timing Using Capacitance Tip Clearance Probes , 2003 .

[9]  Mehmet Imregun,et al.  An improved single-parameter tip-timing method for turbomachinery blade vibration measurements using optical laser probes , 1996 .

[10]  Fabrice Thouverez,et al.  Simulation of Tip-Timing Measurements of a Cracked Bladed Disk Forced Response , 2010 .

[11]  Zheng Hu,et al.  Sparse reconstruction of blade tip-timing signals for multi-mode blade vibration monitoring , 2016 .

[12]  Teresa Maria Berruti,et al.  Synchronous vibration parameters identification by tip timing measurements , 2017 .

[13]  Jan R. Wright,et al.  A class of methods for the analysis of Blade Tip Timing Data from bladed assemblies undergoing simultaneous resonances. Part I: Theoretical Development , 2007 .

[14]  Arnold Kühhorn,et al.  Efficient Generation of Engine Representative Tip Timing Data Based on a Reduced Order Model For Bladed Rotors , 2018 .

[15]  P. Russhard,et al.  Derived once per rev signal generation for Blade Tip Timing systems , 2014 .

[16]  Olivier Jousselin,et al.  Development of blade tip timing techniques in turbo machinery , 2013 .

[17]  Steve Heath.  A New Technique for Identifying Synchronous Resonances Using Tip-Timing , 2000 .

[18]  Philip Bonello,et al.  The Determination of Steady-State Movements Using Blade Tip Timing Data , 2018, Volume 7C: Structures and Dynamics.

[19]  Pete Russhard,et al.  Blade tip timing (BTT) uncertainties , 2016 .

[20]  Teresa Maria Berruti,et al.  Forced response of rotating bladed disks: Blade Tip-Timing measurements , 2017 .