Analytical core loss models for planar inductors with non-uniform flux distribution and non-sinusoidal excitation

In today's state-of-the-art designs, bulky magnetic components pose major barriers to integrate a DC/DC converter into a single chip. One of the promising technologies to integrate the magnetic component with the active component is three-dimensional (3D) integration, using a low-profile inductor as the substrate. In order to optimize low-profile inductor design for high-frequency applications, the core loss of a low-profile inductor should be modeled. However, most low-profile planar inductors have very non-uniform flux distribution. Therefore, previous core loss models, which are based on uniform flux distribution, cannot be used. In addition to non-uniform flux distribution, some planar inductors, such as low-temperature co-fired ceramics (LTCC) inductors, also have non-linear permeability, which makes modeling the core loss for planar inductors even more unconventional and complicated. This paper proposes some analytical core loss models for different low-profile planar inductor structures with non-uniform flux distributions and non-linear permeability. These analytical models also consider non-sinusoidal excitations and the impact of dc bias on core loss. Based on LTCC technology, several low-profile planar inductors are fabricated to help verify these core loss models, and the measured core loss closely match the predicted results, which means the proposed analytical core loss models have very good accuracy.

[1]  Hideo Saotome,et al.  Iron loss analysis of Mn-Zn ferrite cores , 1997 .

[2]  Khai D. T. Ngo,et al.  A Hammerstein-based dynamic model for hysteresis phenomenon , 1997 .

[3]  S.C.O. Mathuna,et al.  PCB integrated inductors for low power DC/DC converter , 2003 .

[4]  G. Bertotti.  Hysteresis in Magnetism: For Physicists, Materials Scientists, and Engineers , 1998 .

[5]  C.R. Sullivan,et al.  Improved calculation of core loss with nonsinusoidal waveforms , 2001, Conference Record of the 2001 IEEE Industry Applications Conference. 36th IAS Annual Meeting (Cat. No.01CH37248).

[6]  Fred C. Lee,et al.  New Core Loss Measurement Method for High-Frequency Magnetic Materials , 2010, IEEE Transactions on Power Electronics.

[7]  R. D. De Doncker,et al.  Calculation of losses in ferro- and ferrimagnetic materials based on the modified Steinmetz equation , 1999, Conference Record of the 1999 IEEE Industry Applications Conference. Thirty-Forth IAS Annual Meeting (Cat. No.99CH36370).

[8]  J.A. Ferreira,et al.  Design method and material technologies for passives in printed circuit Board Embedded circuits , 2005, IEEE Transactions on Power Electronics.

[9]  G. Bertotti.  General properties of power losses in soft ferromagnetic materials , 1988 .

[10]  D. O'Sullivan,et al.  Microfabricated inductors for 20 MHz Dc-Dc converters , 2008, 2008 Twenty-Third Annual IEEE Applied Power Electronics Conference and Exposition.

[11]  T. Durbaum,et al.  Calculating core losses in transformers for arbitrary magnetizing currents a comparison of different approaches , 1996, PESC Record. 27th Annual IEEE Power Electronics Specialists Conference.

[12]  K. H. Carpenter.  Simple models for dynamic hysteresis which add frequency-dependent losses to static models , 1998 .

[13]  W. Roshen.  Ferrite core loss for power magnetic components design , 1991 .

[14]  Chas.P. Steinmetz,et al.  On the law of hysteresis , 1984, Proceedings of the IEEE.

[15]  Fred C. Lee,et al.  A method for inductor core loss estimation in power factor correction applications , 2002, APEC. Seventeenth Annual IEEE Applied Power Electronics Conference and Exposition (Cat. No.02CH37335).

[16]  I. Batarseh,et al.  Design and Fabrication of Integrated Power Inductor Based on Silicon Molding Technology , 2007, 2007 IEEE Power Electronics Specialists Conference.

[17]  E. Waffenschmidt,et al.  Integrated design procedure for printed circuit board inductors in DC-to- DC converters , 2007, 2007 European Conference on Power Electronics and Applications.

[18]  F. Lee,et al.  A Class of Ceramic-Based Chip Inductors for Hybrid Integration in Power Supplies , 2008, IEEE Transactions on Power Electronics.

[19]  Fred C. Lee,et al.  High Inductance Density Low-Profile Inductor Structure for Integrated Point-of-Load Converter , 2009, 2009 Twenty-Fourth Annual IEEE Applied Power Electronics Conference and Exposition.

[20]  Fred C. Lee,et al.  A new high frequency inductor loss measurement method , 2011, 2011 IEEE Energy Conversion Congress and Exposition.

[21]  Fred C. Lee,et al.  Magnetic characterization of low temperature co-fired ceramic (LTCC) ferrite materials for high frequency power converters , 2011, 2011 IEEE Energy Conversion Congress and Exposition.