Evaluation of Hardness and Microstructural Features in Piston Aluminum-Silicon Alloys after Different Ageing Heat Treatments

[1]  Mohammad Sadegh Yazdan Parast,et al.  Effect of Nano-Clay Particles and Heat Treating on Pure and Fretting Fatigue Properties of Piston Aluminum Alloy under Stress-Controlled Cyclic Bending Loading , 2022, Journal of Materials Engineering and Performance.

[2]  Mohammad Sadegh Yazdan Parast,et al.  Data analysis of high-cycle fatigue testing on piston aluminum-silicon alloys under various conditions: Wear, lubrication, corrosion, nano-particles, heat-treating, and stress , 2022, Data in brief.

[3]  M. Azadi,et al.  Effect of plasma nitriding on high‐cycle fatigue properties and fracture behaviors of GJS700 nodular cast iron under cyclic bending loading , 2021, Fatigue & Fracture of Engineering Materials & Structures.

[4]  M. Alphonse,et al.  Effect of heat treatment on mechanical properties of forged aluminium alloy AA2219 , 2021 .

[5]  M. Bhuyan,et al.  Investigating the effect of water cooling on hardness of 2xxx series aluminium alloy micro-alloyed with 0.02 and 0.04 wt% of Titanium , 2021 .

[6]  P. Liu,et al.  Effect of heat treatment on microstructure, hardness and corrosion resistance of 7075 Al alloys fabricated by SLM , 2020 .

[7]  C. Ravindran,et al.  Effects of solution heat treatment time on the as-quenched microstructure, hardness and electrical conductivity of B319 aluminum alloy , 2020 .

[8]  G. Winter,et al.  Evaluation of tensile and low-cycle fatigue properties at elevated temperatures in piston aluminum-silicon alloys with and without nano-clay-particles and heat treatment , 2020 .

[9]  S. Chelladurai,et al.  Prediction of hardness of stir cast LM13 aluminum alloy ‐ copper coated short steel fiber reinforced composites using response surface methodology , 2020, Materialwissenschaft und Werkstofftechnik.

[10]  E. F. A. Zeid.  Influence of Aging Temperature on Precipitation Kinetics, Morphology and Hardening Behavior of Al-7475 Alloy , 2019, Arabian Journal for Science and Engineering.

[11]  M. Azadi,et al.  Effects of Various Ageing Heat Treatments on Microstructural Features and Hardness of Piston Aluminum Alloy , 2019, International Journal of Engineering.

[12]  M. Azadi,et al.  An evaluation of tribological and mechanical properties of Al-Si-Cu alloy with nano-clay particles reinforcement , 2019, Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science.

[13]  S. Qamar,et al.  Optimum heat treatment of aluminum alloy used in manufacturing of automotive piston components , 2018 .

[14]  M. Manoj,et al.  Effect of ageing time and temperature on corrosion behaviour of aluminum alloy 2014 , 2018 .

[15]  Usman Ali,et al.  Electrospun Fibrous Scaffolds for Small-Diameter Blood Vessels: A Review , 2018, Membranes.

[16]  Iloabachie Icc.  Effect of Water Quenching Temperatures on the Hardness ofAl-4.5%Cu , 2018 .

[17]  W. Sha,et al.  Observation of fretting fatigue cracks of Ti6Al4V titanium alloy , 2017 .

[18]  T. Prabhu.  Effects of ageing time on the mechanical and conductivity properties for various round bar diameters of AA 2219 Al alloy , 2017 .

[19]  Qiang-Yan Xu,et al.  Study of precipitation in Al–Mg–Si alloys by Atom Probe Tomography I. Microstructural changes as a function of ageing temperature , 2015 .

[20]  R. Daud,et al.  Effect of Heat Treatment on Microstructure, Hardness and Wear of Aluminum Alloy 332 , 2015 .

[21]  S. H. Juang,et al.  Influence of preheating temperatures and adding rates on distributions of fly ash in aluminum matrix composites prepared by stir casting , 2015 .

[22]  D. S. Yawas,et al.  Effects of Pressure on the Mechanical Properties and Microstructure of Die Cast Aluminum A380 Alloy , 2014 .

[23]  D. Larouche,et al.  Application of cast Al–Si alloys in internal combustion engine components , 2014 .

[24]  G. Requena,et al.  The effect of spheroidisation heat treatment on the creep resistance of a cast AlSi12CuMgNi piston alloy , 2014 .

[25]  P. Sharma,et al.  Design, Analysis and Optimization of Three Aluminium Piston Alloys Using FEA , 2014 .

[26]  S. I. Talabi,et al.  Effects of Heat Treatment on the Mechanical Properties of Al-4% Ti Alloy , 2013 .

[27]  R. Khosroshahi,et al.  Mechanical and wear properties of Al-Al3Mg2 nanocomposites prepared by mechanical milling and hot pressing , 2013, International Journal of Minerals, Metallurgy, and Materials.

[28]  A. Sarhan,et al.  The influence of higher surface hardness on fretting fatigue life of hard anodized aerospace AL7075-T6 alloy , 2013 .

[29]  A. Hossain,et al.  Effect of Ageing Temperature on the Mechanical Properties of Al-6Si-0.5Mg Cast Alloys with Cu Additions Treated by T6 Heat Treatment , 2013 .

[30]  S. El-Raghy,et al.  Effect of aging time at low aging temperatures on the corrosion of aluminum alloy 6061 , 2012 .

[31]  S. Manasijevic,et al.  Thermal analysis and microscopic characterization of the piston alloy AlSi13Cu4Ni2Mg , 2011 .

[32]  Xiangfa Liu,et al.  Quantitative comparison of three Ni-containing phases to the elevated-temperature properties of Al-Si piston alloys , 2010 .

[33]  R. C. Picu,et al.  Influence of aging treatment on mechanical properties of 6061 aluminum alloy , 2010 .

[34]  F. Nový,et al.  Microstructure changes in a 2618 aluminium alloy during ageing and creep , 2009 .

[35]  Guohua Zhang,et al.  Effects of trace Mn addition on the elevated temperature tensile strength and microstructure of a low-iron Al–Si piston alloy , 2008 .

[36]  Muzaffer Zeren,et al.  The effect of heat-treatment on aluminum-based piston alloys , 2007 .

[37]  A. Moffat,et al.  The effect of silicon content on long crack fatigue behaviour of aluminium-silicon piston alloys at elevated temperature , 2005 .

[38]  J. Sieniawski,et al.  Influence of heat treatment on the microstructure and mechanical properties of 6005 and 6082 aluminium alloys , 2005 .

[39]  H. Ye,et al.  An overview of the development of Al-Si-Alloy based material for engine applications , 2003 .

[40]  R. Colás,et al.  Precipitation in a heat-treatable aluminum alloy cooled at different rates , 2001 .