Thermal-Mechanical Analysis of a Low-Enriched Uranium Foil Based Annular Target for the Production of Molybdenum-99

One of the US Department of Energy’s Global Threat Reduction Initiative (GTRI) goals is the elimination of the use of high enriched uranium (HEU) for the production of the radioisotope molybdenum-99 (Mo-99). One strategy to achieve this goal is to use an irradiation target that utilizes a low-enriched uranium (LEU) foil. This paper considers an annular target geometry, where an LEU foil of open cross section is sandwiched between two concentric aluminum tubes. A recess is cut on the inner tube to hold the LEU foil and facilitate assembly. The target must contain the fission products until it can be opened and the LEU foil removed for further processing. The thermal contact resistance between the LEU foil and the aluminum tube cladding needs to be low enough to ensure that the LEU temperature does not exceed the operating temperature specified by the reactor safety case.Numerical models using the commercial finite element code Abaqus FEA are used to explore the potential for gaps opening between the LEU-foil and the aluminum tubes, and the stresses developed in the aluminum tubes during heat generation in the target during irradiation. Parametric studies are conducted using constructed analytic models to explore the impact of the ratio of heat transfer coefficients between the inner and the outer tubes and the inner-to-outer tube thickness ratio. It is concluded that the current annular target design is safe at high LEU heat generation rates and the use of these targets will likely not compromise the reactor safety.Copyright © 2012 by ASME

[1]  C. V. Madhusudana,et al.  Thermal conductance of cylindrical joints , 1999 .

[2]  R. Zimmerman,et al.  Thermal stresses and thermal expansion in a uniformly heated functionally graded cylinder , 1999 .

[3]  I. I. Novikov,et al.  Experimental investigation of contact heat exchange between coaxial cylindrical casings in vacuum , 1972 .

[4]  Maria Comninou,et al.  On Lack of Uniqueness in Heat Conduction through a Solid to Solid Contact , 1980 .

[5]  J. L. Snelgrove,et al.  Development of annular targets for {sup 99}MO production. , 1999 .

[6]  Leroy S. Fletcher,et al.  Solid Spot Thermal Conductance of Zircaloy-2/Uranium Dioxide Interfaces , 1983 .

[7]  R. B. Scott,et al.  HEAT CONDUCTION THROUGH INSULATING SUPPORTS IN VERY LOW TEMPERATURE EQUIPMENT , 1956 .

[8]  A. Ugural,et al.  Advanced strength and applied elasticity , 1981 .

[9]  K. C. Jane,et al.  Thermoelasticity of multilayered cylinders , 1999 .

[10]  Ning Hu,et al.  Thermal Stress Analysis of Sandwich Structures , 2006 .

[11]  Masood Iqbal,et al.  Low enriched uranium foil plate target for the production of fission Molybdenum-99 in Pakistan Research Reactor-1 , 2009 .

[12]  M. Cooper,et al.  Thermal contact conductance , 1969 .

[13]  Gary L. Solbrekken,et al.  Thermal-Mechanical Analysis of Annular Target Design for High Volume Production of Molybdenum-99 Using Low-Enriched Uranium , 2009 .

[14]  M. G. Srinivasan.  Nonuniqueness in Steady-State Heat Transfer in Prestressed Duplex Tubes—Analysis and Case History , 1985 .

[15]  Martin Raynaud,et al.  Estimation of thermal Contact Resistance Between the Materials of Double-Layer Sample Using the Laser Flash Method , 2002 .

[16]  S. Timoshenko,et al.  Theory of elasticity , 1975 .

[17]  Hillel Poritsky,et al.  Analysis of Thermal Stresses in Sealed Cylinders and the Effect of Viscous Flow During Anneal , 1934 .

[18]  A. Mutalib,et al.  Full-scale demonstration of the cintichem process for the production of Mo-99 using a low-enriched target. , 1998 .

[19]  Yu-Ching Yang, Haw-Long Lee.  COUPLED THERMOELASTICITY OF AN INFINITELY LONG, TRIPLE-LAYER ANNULAR CYLINDER , 2001 .