Oil film lifetime and wear particle analysis of laser-patterned stainless steel surfaces

Abstract In this experimental study, periodic cross-like patterns with different structural wavelengths (6 and 9 µm) were fabricated by laser-interference patterning on stainless steel samples (AISI-304). Tribological tests with a ball-on-disc tribometer in rotational sliding mode were performed under mixed lubrication. Spin coating was used to produce homogeneously distributed oil films with a defined initial oil film thickness in order to ensure reproducible testing conditions for all tested samples. By means of an advanced electrical resistivity circuit, a sharp increase in the coefficient of friction was well correlated with a change in the lubrication regime from mixed to boundary lubrication. This event defines the oil film lifetime at the corresponding cycle count. An oil film lifetime of 1000 sliding cycles was determined for the polished reference samples which is independent of the initial oil film thickness. For the laser-patterned surfaces, the oil film lifetime increases with decreasing initial oil film thickness. Moreover, the cross-like pattern with a structural wavelength of 6 µm shows a significant improvement in the oil film lifetime by a factor of 130 compared to the unpatterned reference. A subsequent analysis of the wear particles was able to demonstrate that the wear particles being produced for the laser-patterned surfaces are typically smaller than half of the used structural wavelength. As a consequence, the produced wear particles can be effectively trapped in the topographic minima positions. Consequently, those particles do not remain in the contact area thus reducing the abrasive wear component and increasing the oil film lifetime.

[1]  Nam P. Suh,et al.  An overview of the delamination theory of wear , 1977 .

[2]  A. M. Merlo,et al.  The contribution of surface engineering to the product performance in the automotive industry , 2003 .

[3]  Kristian Tønder,et al.  Inlet roughness tribodevices: dynamic coefficients and leakage , 2001 .

[4]  Simon C. Tung,et al.  Automotive tribology overview of current advances and challenges for the future , 2004 .

[5]  Staffan Jacobson,et al.  Influence of surface texture on boundary lubricated sliding contacts , 2003 .

[6]  A. Gosman,et al.  Entrainment and Inlet Suction: Two Mechanisms of Hydrodynamic Lubrication in Textured Bearings , 2007 .

[7]  Koji Kato,et al.  Wear in relation to friction — a review , 2000 .

[8]  Pawel Pawlus,et al.  Abrasive wear resistance of textured steel rings , 2009 .

[9]  Yukio Tateishi.  Tribological issues in reducing piston ring friction losses , 1994 .

[10]  I. Etsion,et al.  Improving fuel efficiency with laser surface textured piston rings , 2009 .

[11]  I. Křupka,et al.  Behavior of real roughness features within mixed lubricated non-conformal contacts , 2008 .

[12]  Izhak Etsion,et al.  A Laser Surface Textured Parallel Thrust Bearing , 2003 .

[13]  A. R. Rosenfield,et al.  Wear processes in sliding systems , 1984 .

[14]  Andreas A. Polycarpou,et al.  Friction characteristics of microtextured surfaces under mixed and hydrodynamic lubrication , 2013 .

[15]  Dong Zhu,et al.  Virtual Texturing: Modeling the Performance of Lubricated Contacts of Engineered Surfaces , 2005 .

[16]  Izhak Etsion,et al.  Friction-Reducing Surface-Texturing in Reciprocating Automotive Components , 2001 .

[17]  T B Lane,et al.  A study of the oil-film formation in gears by electrical resistance measurements , 1952 .

[18]  Roland Larsson,et al.  Two-Dimensional CFD-Analysis of Micro-Patterned Surfaces in Hydrodynamic Lubrication , 2005 .

[19]  Sergej M. Pimenov,et al.  Lubricated sliding performance of laser-patterned sapphire , 1999 .

[20]  A. Lasagni,et al.  Micro/Nano Fabrication of Periodic Hierarchical Structures by Multi‐Pulsed Laser Interference Structuring , 2007 .

[21]  Izhak Etsion,et al.  The Effect of Laser Texturing of Steel Surfaces and Speed-Load Parameters on the Transition of Lubrication Regime from Boundary to Hydrodynamic , 2004 .

[22]  The Effect of Lubricant Viscosity on Metallic Contact and Friction in a Sliding System , 1962 .

[23]  R. I. Taylor,et al.  Improved fuel efficiency by lubricant design: A review , 2000 .

[24]  Diego Marchetto,et al.  Tribological effects of surface texturing on nitriding steel for high-performance engine applications , 2008 .

[25]  M. E. Salama,et al.  The Effect of Macro-Roughness on the Performance of Parallel Thrust Bearings: , 1950 .

[26]  Richard C. Rosenberg,et al.  General Friction Considerations for Engine Design , 1982 .

[27]  D. Dowson.  History of Tribology , 1979 .

[28]  Oyelayo O. Ajayi,et al.  Friction and wear behavior of laser textured surface under lubricated initial point contact , 2011 .

[29]  Shinya Sasaki,et al.  The influence of bulges produced by laser surface texturing on the sliding friction and wear behavior , 2013 .

[30]  S. Ge,et al.  Hydrodynamic Lubrication of Microdimple Textured Surface Using Three-Dimensional CFD , 2010 .

[31]  Nam P. Suh,et al.  The relationship between crack propagation rates and wear rates , 1977 .

[32]  Shuji Sakaguchi,et al.  Tribological properties of dimpled silicon nitride under oil lubrication , 2004 .

[33]  Litian Hu,et al.  The study of tribological properties of laser‐textured surface of 2024 aluminium alloy under boundary lubrication , 2012 .

[34]  Hugh Spikes,et al.  Basics of mixed lubrication , 2003 .

[35]  Izhak Etsion,et al.  The Validity of the Reynolds Equation in Modeling Hydrostatic Effects in Gas Lubricated Textured Parallel Surfaces , 2006 .

[36]  Hugh Spikes,et al.  ‘Inlet suction’, a load support mechanism in non-convergent, pocketed, hydrodynamic bearings , 2006 .

[37]  J. A. Walowit,et al.  A Theory of Lubrication by Microirregularities , 1966 .

[38]  Kenneth Holmberg,et al.  Global energy consumption due to friction in passenger cars , 2012 .

[39]  Nam P. Suh,et al.  Mechanics of crack propagation in delamination wear , 1977 .

[40]  K. To̸nder.  Dynamics of rough slider bearings: effects of one-sided roughness/waviness , 1996 .

[41]  Kristian Tønder,et al.  Hydrodynamic effects of tailored inlet roughnesses: extended theory , 2004 .

[42]  Valerio Romano,et al.  Laser microstructuring of steel surfaces for tribological applications , 2000 .

[43]  I. Etsion,et al.  Improving Tribological Performance of Piston Rings by Partial Surface Texturing , 2005 .

[44]  Pawel Pawlus,et al.  The effect of oil pockets size and distribution on wear in lubricated sliding , 2007 .

[45]  C. M. Taylor,et al.  Automobile Engine Tribology - Approaching the Surface , 2000 .

[46]  M. Fillon,et al.  Analytical investigation of a partially textured parallel slider , 2009 .

[47]  P. Pawlus,et al.  The effect of surface texturing on seizure resistance of a steel–bronze assembly , 2010 .

[48]  Izhak Etsion,et al.  The effect of laser surface texturing on transitions in lubrication regimes during unidirectional sliding contact. , 2005 .

[49]  P. Pawlus,et al.  Experimental investigation of oil pockets effect on abrasive wear resistance , 2011 .

[50]  Carsten Gachot,et al.  Correlation between solid–solid contact ratios and lubrication regimes measured by a refined electrical resistivity circuit , 2014 .

[51]  Martin Hartl,et al.  The effect of surface texturing on thin EHD lubrication films , 2007 .

[52]  M. Fillon,et al.  Optimizing surface texture for hydrodynamic lubricated contacts using a mass-conserving numerical approach , 2010 .

[53]  Frank Mücklich,et al.  Increasing Lubricant Film Lifetime by Grooving Periodical Patterns Using Laser Interference Metallurgy , 2008 .

[54]  Dong Zhu,et al.  Friction Reduction in Mixed Lubrication , 2007 .

[55]  Peter Andersson,et al.  Microlubrication effect by laser-textured steel surfaces , 2007 .

[56]  I. Etsion,et al.  Testing piston rings with partial laser surface texturing for friction reduction , 2006 .

[57]  Pawel Pawlus,et al.  Dimples shape and distribution effect on characteristics of Stribeck curve , 2009 .

[58]  M. J. Furey,et al.  Surface Roughness Effects on Metallic Contact and Friction , 1963 .

[59]  N. Suh,et al.  Boundary Lubrication of Undulated Metal Surfaces at Elevated Temperatures , 1989 .

[60]  I. Křupka,et al.  Effect of surface texturing on mixed lubricated non-conformal contacts , 2008 .

[61]  I. Křupka,et al.  Effect of surface texturing on rolling contact fatigue within mixed lubricated non-conformal rolling/sliding contacts , 2010 .

[62]  Martin Hartl,et al.  Effect of surface topography on mixed lubrication film formation during start up under rolling/sliding conditions , 2010 .

[63]  P. Pawlus,et al.  The Effect of Oil Pockets Shape and Distribution on Seizure Resistance in Lubricated Sliding , 2010 .

[64]  M. Dienwiebel,et al.  In situ observation of wear particle formation on lubricated sliding surfaces , 2012 .

[65]  Stephen M. Hsu,et al.  Boundary lubricating films: formation and lubrication mechanism , 2005 .

[66]  F. Mücklich,et al.  Contact Mechanics of Laser-Textured Surfaces , 2013, Tribology Letters.

[67]  Nam P. Suh,et al.  Boundary Lubrication Studies on Undulated Titanium Surfaces , 1989 .

[68]  M. J. Furey,et al.  Metallic Contact and Friction between Sliding Surfaces , 1961 .

[69]  L. M. Vilhena,et al.  Effectiveness and design of surface texturing for different lubrication regimes , 2012 .

[70]  H. Spikes.  Mixed lubrication — an overview , 1997 .

[71]  Staffan Jacobson,et al.  Friction and Wear Properties of Micro Textured DLC Coated Surfaces in Boundary Lubricated Sliding , 2004 .

[72]  H. Czichos,et al.  Rapid measuring techniques for electrical contact resistance applied to lubricant additives studies , 1976 .