Study of Ice Accretion on Horizontal Axis Wind Turbine Blade Using 2D and 3D Numerical Approach

In order to optimize the wind turbine operation in ice prone cold regions, it is important to better understand the ice accretion process and how it affects the wind turbine performance. In this paper, Computational Fluid Dynamics (CFD) based 2D and 3D numerical techniques are used to simulate the airflow/droplet behaviour and resultant ice accretion on a 300 kW wind turbine blade. The aim is to better understand the differences in the flow behaviour and resultant ice accretion between both approaches, as typically the study of ice accretion on the wind turbine blade is performed using simple 2D simulations, where the 3D effects of flow (air & droplet) are ignored, which may lead to errors in simulated ice accretion. For 2D simulations, nine sections along a 300 kW wind turbine blade are selected, whereas for 3D study, a full-scale blade is used. The obtained results show a significant difference in the ice accretion for both approaches. Higher ice growth is observed in 2D approach when compared with the full-scale 3D simulations. CFD simulations are carried out for three different icing conditions (typical, moderate and extreme), in order to estimate the extent of differences the different operating conditions can introduce on the ice accretion process in the 2D and the 3D simulations. Complex ice shapes are observed in case of extreme ice conditions, which affect the aerodynamic performance of the blade differently from typical and moderate ice conditions.

[1]  Christian Masson,et al.  Atmospheric icing impact on wind turbine production , 2014 .

[2]  CFD study of airfoil lift reduction caused by ice roughness , 2018, 2018 Applied Aerodynamics Conference.

[3]  Taeseong Kim,et al.  Development of an icing simulation code for rotating wind turbines , 2020 .

[4]  Wagdi G. Habashi,et al.  FENSAP-ICE's Three-Dimensional In-Flight Ice Accretion Module: ICE3D , 2003 .

[5]  Masoud Mirzaei,et al.  Experimental study of ice accretion effects on aerodynamic performance of an NACA 23012 airfoil , 2016 .

[6]  R. Benoit,et al.  Canadian icing envelopes near the surface and its impact on wind energy assessment , 2015 .

[7]  Reza S. Abhari,et al.  The Impact of Ice Formation on Wind Turbine Performance and Aerodynamics , 2011 .

[8]  Muhammad S. Virk,et al.  Accreted ice mass ratio(k‐factor)for rotating wind turbine blade profile and circular cylinder , 2019, Wind Energy.

[9]  Neil N. Davis.  Icing Impacts on Wind Energy Production , 2014 .

[10]  H. Holttinen,et al.  Wind energy production in cold climate (WECO) , 2000 .

[11]  Yuhang Wang,et al.  Study on the glaze ice accretion of wind turbine with various chord lengths , 2018 .

[12]  Colin S Bidwell,et al.  USERS MANUAL FOR THE NASA LEWIS THREE-DIMENSIONAL ICE ACCRETION CODE (LEWICE 3D). , 1993 .

[13]  Muhammad S. Virk,et al.  Study of ice accretion along symmetric and asymmetric airfoils , 2018 .

[14]  Jonghwa Kim,et al.  Study on correlation between wind turbine performance and ice accretion along a blade tip airfoil using CFD , 2018 .

[15]  William B. Wright,et al.  User Manual for the NASA Glenn Ice Accretion Code LEWICE: Version 2.0 , 1999 .

[16]  Torgeir Moan,et al.  Wind turbine aerodynamic response under atmospheric icing conditions , 2014 .

[17]  Wagdi G. Habashi,et al.  FENSAP-ICE Simulation of Complex Wind Turbine Icing Events, and Comparison to Observed Performance Data , 2014 .

[18]  Xingliang Jiang,et al.  3D numerical simulation of aerodynamic performance of iced contaminated wind turbine rotors , 2018 .

[19]  Farooq Saeed,et al.  State-of-the-Art Aircraft Icing and Anti-Icing Simulation , 2003 .

[20]  W. A. Timmer.  Aerodynamic characteristics of wind turbine blade airfoils at high angles-of-attack , 2010 .