The assessment of wind conditions by means of hot wire sensors and a modifed Wheatstone bridge architecture

Abstract In this paper we present a novel complete anemometric electronic system based on an array of hot wire sensors, provided by Telecontrolli SME, and a suitable heater feedback that achieves, thanks to a dedicated algorithm, a CMOS integrable portable solution showing a robust design, without moving parts and small dimensions. The sensor interface is implemented by means of a modified Wheatstone bridge architecture with autobalancing capability. Comparisons with a commercial cup anemometer have shown that the proposed architecture, with reduced space occupancy and low power consumption, is suitable to operate in a natural environment in the −20 to +55 °C temperature range providing wind speed and direction measurement. Concerning the wind speed, a 0.6 m/s sensitivity has been achieved. The integrated CMOS design of the final system is also presented and discussed in the paper.

[1]  Zhen Fang,et al.  A directional anemometer based on MEMS differential pressure sensors , 2014, The 9th IEEE International Conference on Nano/Micro Engineered and Molecular Systems (NEMS).

[2]  Kenzo Watanabe,et al.  A silicon micromachined flow sensor using thermopiles for heat transfer measurements , 2003, IEEE Trans. Instrum. Meas..

[3]  José Sérgio da Rocha Neto,et al.  Dynamic response of thermoresistive sensors , 1992 .

[4]  V. S. G. Martins,et al.  Sensitivity analysis and automatic adjustment of a controlled-temperature thermoresistive-based anemometer , 2012, 2012 IEEE International Instrumentation and Measurement Technology Conference Proceedings.

[5]  Shahram Minaei,et al.  Single voltage controlled CMOS grounded resistors and their application to video filter , 2014 .

[6]  Raimundo Carlos Silvério Freire,et al.  Applications of Thermoresistive Sensors Using the Electric Equivalence Principle , 2009, IEEE Transactions on Instrumentation and Measurement.

[7]  H. Tam,et al.  All-optical fiber anemometer based on laser heated fiber Bragg gratings. , 2011, Optics express.

[8]  G. R. Sarma.  Analysis of a constant voltage anemometer circuit , 1993, 1993 IEEE Instrumentation and Measurement Technology Conference.

[9]  Vincenzo Stornelli,et al.  Full range analog Wheatstone bridge‐based automatic circuit for differential capacitance sensor evaluation , 2017, Int. J. Circuit Theory Appl..

[10]  F. Feyzi,et al.  Development of two multisensor hot-film measuring techniques for free-flight experiments , 1989, International Congress on Instrumentation in Aerospace Simulation Facilitie.

[11]  J.Y.M. Perez,et al.  Arrangement Of Temperature Sensors As A Wind Sensor , 2006, 2006 3rd International Conference on Electrical and Electronics Engineering.

[12]  Robin Bargar,et al.  Circuits for voltage tuning the parameters of Chua's circuit: Experimental application for musical signal generation , 1994 .

[13]  R.C.S. Freire,et al.  Dependence of a Thermoresistive Sensor-Based Constant Temperature Measurement Instrument Response on DC Amplifier Input Offset Voltage , 2005, 2005 IEEE Instrumentationand Measurement Technology Conference Proceedings.

[14]  Leonardo Pantoli,et al.  A Low Cost Fully Integrable in a Standard CMOS Technology Portable System for the Assessment of Wind Conditions , 2016 .

[15]  Raimundo Carlos Silvério Freire,et al.  Hot-wire anemometer with temperature compensation using only one sensor , 2001, IEEE Trans. Instrum. Meas..

[16]  Kevin P. Chen,et al.  X-probe flow sensor using self-powered active fiber Bragg gratings , 2006 .

[17]  M. Elwenspoek,et al.  A new class of thermal flow sensors using /spl Delta/T=0 as a control signal , 2000, Proceedings IEEE Thirteenth Annual International Conference on Micro Electro Mechanical Systems (Cat. No.00CH36308).

[18]  Sekwang Park,et al.  Two-dimensional ultrasonic anemometer using the directivity angle of an ultrasonic sensor , 2008, Microelectron. J..

[19]  P. Bruschi,et al.  A Low-Power 2-D Wind Sensor Based on Integrated Flow Meters , 2009, IEEE Sensors Journal.

[20]  G. S. Deep,et al.  Compensation of the fluid temperature variation in a hot-wire anemometer , 1997, IEEE Instrumentation and Measurement Technology Conference Sensing, Processing, Networking. IMTC Proceedings.

[21]  Masoud Farzaneh,et al.  Coupled Computational Fluid Dynamics and Heat Transfer Modeling of the Effects of Wind Speed and Direction on Temperature Increase of an Ice-Covered FRP Live-Line Tool , 2015, IEEE Transactions on Power Delivery.

[22]  M.A. Moreira,et al.  Sensors Characterization and Control of Measurement Systems with Thermoresistive Sensors using Feedback Linearization , 2008, 2008 IEEE Instrumentation and Measurement Technology Conference.

[23]  W. T. Eckert,et al.  Aerodynamic design guidelines and computer program for estimation of subsonic wind tunnel performance , 1976 .

[24]  Vincenzo Stornelli,et al.  Integrated Rail-to-Rail Low-Voltage Low-Power Enhanced DC-Gain Fully Differential Operational Transconductance Amplifier , 2007 .

[25]  Vincenzo Stornelli.  Low voltage Low Power Fully Differential Buffer , 2009, J. Circuits Syst. Comput..

[26]  Massimo Piotto,et al.  Fabrication and characterization of a directional anemometer based on a single chip MEMS flow sensor , 2011 .