An experimental study on the applicability of acoustic emission for wind turbine gearbox health diagnosis

Condition monitoring of wind turbine gearboxes has mainly relied upon vibration, oil analysis and temperature monitoring. However, these techniques are not well suited for detecting early stage damage. Acoustic emission is gaining ground as a complementary condition monitoring technique as it offers earlier fault detection capability compared with other more established techniques. The objective of early fault detection in wind turbine gearboxes is to avoid unexpected catastrophic breakdowns, thereby reducing maintenance costs and increase safety. The aim of this investigation is to present an experimental study the impact of operational conditions (load and torque) in the acoustic emission activity generated within the wind turbine gearbox. The acoustic emission signature for a healthy wind turbine gearbox was obtained as a function of torque and power output, for the full range of operational conditions. Envelope analysis was applied to the acoustic emission signals to investigate repetitive patterns and correlate them with specific gearbox components. The analysis methodology presented herewith can be used for the reliable assessment of wind turbine gearbox subcomponents using acoustic emission.

[1]  Stephan Ebersbach,et al.  The investigation of the condition and faults of a spur gearbox using vibration and wear debris analysis techniques , 2006 .

[2]  D Mba,et al.  Condition monitoring of slow-speed rolling element bearings using stress waves , 2001 .

[3]  Sun Wenlei,et al.  Vibration and Noise Radiation Characteristics of Gear Transmission System , 2014 .

[4]  S. Al-Dossary,et al.  Observations of changes in acoustic emission waveform for varying seeded defect sizes in a rolling element bearing , 2009 .

[5]  D Mba,et al.  Bearing defect diagnosis and acoustic emission , 2003 .

[6]  S. Butterfield,et al.  Improving Wind Turbine Gearbox Reliability , 2007 .

[7]  Y. Pao,et al.  Acoustic emission and transient waves in an elastic plate , 1979 .

[8]  Pavel Mazal,et al.  An experimental investigation of rolling contact fatigue of steels using acoustic emission method , 2013 .

[9]  B. P. McNiff,et al.  Variations in gear fatigue life for different wind turbine braking strategies , 1991 .

[10]  Helge Aagaard Madsen,et al.  Low Frequency Noise from Wind Turbines Mechanisms of Generation and its Modelling , 2010 .

[11]  David,et al.  Identification of the acoustic emission source during a comparative study on diagnosis of a spur gearbox , 2005 .

[12]  Tat-Hean Gan,et al.  A novel approach for incipient defect detection in rolling bearings using acoustic emission technique , 2015 .

[13]  Joseph Mathew,et al.  Rotating machinery prognostics. State of the art, challenges and opportunities , 2009 .

[14]  Babak Eftekharnejad.  Condition monitoring of gearboxes using acoustic emission , 2010 .

[15]  N. Tandon,et al.  A comparison of some condition monitoring techniques for the detection of defect in induction motor ball bearings , 2007 .

[16]  Slim Soua,et al.  Determination of the combined vibrational and acoustic emission signature of a wind turbine gearbox and generator shaft in service as a pre-requisite for effective condition monitoring , 2013 .

[17]  B. Charnley,et al.  Energy Index technique for detection of Acoustic Emissions associated with incipient bearing failures , 2010 .

[18]  Pan Cunzhi,et al.  Nonlinear Dynamics of a Spur Gear Pair with Time-Varying Stiffness and Backlash , 2004 .

[19]  N. Jamaludin.  Monitoring extremely slow rolling element bearings: part II , 2002 .

[20]  David Mba,et al.  Development of Acoustic Emission Technology for Condition Monitoring andDiagnosis of Rotating Machines; Bearings, Pumps, Gearboxes, Engines and RotatingStructures. , 2006 .

[21]  D. Mba,et al.  Acoustic Emission for the Detection of Shaft-to-Seal Rubbing in Large Power Generation Turbines , 2006 .

[22]  Mohamed Ali Elforjani.  Condition Monitoring of Slow Speed Rotating Machinery Using Acoustic Emission Technology , 2010 .

[23]  DongSik Gu,et al.  Detection of faults in gearboxes using acoustic emission signal , 2011 .

[24]  Tat-Hean Gan,et al.  Shaft angular misalignment detection using acoustic emission , 2014 .

[25]  Victor Baranov,et al.  Acoustic Emission in Friction , 2012 .

[26]  M. Feldman.  Hilbert transform in vibration analysis , 2011 .

[27]  Takashi Yamamoto,et al.  Incipient damage detection and its propagation monitoring of rolling contact fatigue by acoustic emission , 2009 .

[28]  Evangelos Dermatas,et al.  Feature Selection for Robust Classification of Crack and Drop Signals , 2009 .

[29]  Andrew Ball,et al.  Modelling acoustic emissions generated by sliding friction , 2010 .

[30]  Bo-Suk Yang,et al.  Fault diagnosis of low speed bearing based on acoustic emission signal and multi-class relevance vector machine , 2009 .

[31]  Mengyan Nie,et al.  Review of condition monitoring and fault diagnosis technologies for wind turbine gearbox , 2013 .

[32]  David.  Acoustic Emissions and monitoring bearing health , 2003 .

[33]  Tian Ran Lin,et al.  A practical signal processing approach for condition monitoring of low speed machinery using Peak-Hold-Down-Sample algorithm , 2012 .

[34]  M. Elforjani,et al.  Accelerated natural fault diagnosis in slow speed bearings with Acoustic Emission , 2010 .

[35]  David,et al.  A comparative experimental study on the use of acoustic emission and vibration analysis for bearing defect identification and estimation of defect size , 2006 .

[36]  Fulei Chu,et al.  Application of AE techniques for the detection of wind turbine using Hilbert-Huang transform , 2010, 2010 Prognostics and System Health Management Conference.

[37]  B. C. Nakra,et al.  Defect detection in rolling element bearings by acoustic emission method , 1990 .