Die structure optimization for a large, multi-cavity aluminum profile using numerical simulation and experiments

Abstract The steady state extrusion process of a large, multi-cavity aluminum profile for high-speed train was simulated using the Arbitrary Lagrangian Eulerian (ALE) algorithm. The simulation result of the initial design shows that the material flow velocity in the bearing exit is non-uniform. Comparing the obtained extrudate front end of the simulation with the experimental results of the initial design, it is clear that the metal in thick-walled regions of the profiles in both results flows faster than that in the other regions of the profiles. Moreover, the distorted metal in the six inclined ribs shown in both results are very similar to each other. Aiming at a uniform flow velocity, four kinds of structure optimizations were proposed and simulated. The methods of resizing portholes, adding bosses, chamfering mandrels, and adjusting the length of the bearings can balance the local metal flow velocity effectively. Finally, a perfect simulation result with exit velocity difference of 18.7 mm/s and little distortion was obtained. Through the effective prediction of flow velocity in the simulation extrusion, the qualified profiles with few trial and error extrusions were manufactured successfully. The case study demonstrates that the ALE method is a viable predictive tool for die design, and the approach is applicable to the extrusion of other alloys for any other extrudate shapes.

[1]  Guillaume Houzeaux,et al.  The fixed-mesh ALE approach for the numerical approximation of flows in moving domains , 2009, J. Comput. Phys..

[2]  Guoqun Zhao,et al.  Effect of extrusion stem speed on extrusion process for a hollow aluminum profile , 2012 .

[3]  Xueyu Ruan,et al.  Finite volume simulation and mould optimization of aluminum profile extrusion , 2007 .

[4]  Sverre Brandal,et al.  Optimisation of flow balance and isothermal extrusion of aluminium using finite-element simulations , 2011 .

[5]  I. Flitta,et al.  Nature of friction in extrusion process and its effect on material flow , 2003 .

[6]  Zhen Zhao,et al.  Simulation of sheet metal extrusion processes with Arbitrary Lagrangian-Eulerian method , 2008 .

[7]  J Lof,et al.  FEM simulations of the extrusion of complex thin-walled aluminium sections , 2002 .

[8]  Chung-Gil Kang,et al.  Effects of chamber shapes of porthole die on elastic deformation and extrusion process in condenser tube extrusion , 2005 .

[9]  Jie Zhou,et al.  Extrusion of 7075 aluminium alloy through double-pocket dies to manufacture a complex profile , 2009 .

[10]  G. J. Creus,et al.  Simulation of 3D metal-forming using an arbitrary Lagrangian–Eulerian finite element method , 2001 .

[11]  B. Gautham,et al.  Prediction of extrudate swell in polymer melt extrusion using an Arbitrary Lagrangian Eulerian (ALE) based finite element method , 2009 .

[12]  Santosh Kumar,et al.  Die design and experiments for shaped extrusion under cold and hot condition , 2007 .

[13]  Guoqun Zhao,et al.  Numerical Simulation of Extrusion Process and Die Structure Optimization for a Complex Aluminum Multicavity Wallboard of High-Speed Train , 2011 .

[14]  Seon-Bong Lee,et al.  Prediction of Welding Pressure in the Non Steady state Porthole Die Extrusion of AI7003 Tubes , 2002 .

[15]  Dong-Yol Yang,et al.  Design of processes and products through simulation of three-dimensional extrusion , 2007 .

[16]  Jian Wang,et al.  Tribological behavior of Ti2SnC particulate reinforced copper matrix composites , 2006 .

[17]  Ma Xinwu,et al.  Numerical Simulation and Die Structure Optimization of an Aluminum Rectangular Hollow Pipe Extrusion Process , 2006 .

[18]  S. H. Kim,et al.  Investigation of lubrication effect on the backward extrusion of thin-walled rectangular aluminum case with large aspect ratio , 2006 .

[19]  Fu Yao.  Effect of pocket designs on exit velocity during thin-walled aluminium profile extrusion , 2010 .