Erosion of hard surface coatings for use in offshore gate valves

This paper describes the work carried out in assessing the performance of hard chromium, electroless nickel composite and two HVOF tungsten carbide coatings as candidate hard surface coatings for use in offshore gate valves. The coatings were erosion tested in a slurry jet facility and their performance compared with a D-gun 86WC–10Co–4Cr coating that is currently widely used in service. Sand erosion tests were conducted at 28 m s?1 and with 135 and 235 ?m sand, respectively. The eroded surfaces were examined so that the erosion mechanisms of each coating could be determined. The results indicate that the Diatec applied HVOF 86WC–10Co–4Cr coating is the most promising alternative, representing an improvement in erosion resistance of more than 50% over the D-gun applied coating of identical nominal composition. For some applications of low-erosivity, hard chromium may be a more cost-effective option. The variation in the erosion performance of the thermally sprayed coatings is linked to directional fracture toughness and crack propagation paths which are influenced by the presence of pores, inhomogeneous carbide distributions, Co6W6C and substrate grit blast remnants.

[1]  M. E. Gulden.  Correlation of Experimental Erosion Data with Elastic‐Plastic Impact Models , 1981 .

[2]  H. Clark,et al.  The influence of the flow field in slurry erosion , 1992 .

[3]  B. Mellor,et al.  Sand erosion performance of detonation gun applied tungsten carbide/cobalt-chromium coatings , 1997 .

[4]  K. Kembaiyan,et al.  Combating severe fluid erosion and corrosion of drill bits using thermal spray coatings , 1995 .

[5]  V. R. Parameswaran,et al.  Comparison of slurry and dry erosion behaviour of some HVOF thermal sprayed coatings , 1999 .

[6]  S. Roberts,et al.  The effect of impact angle on the erosion rate of polycrystalline α-Al2O3 , 1998 .

[7]  H. Clark,et al.  Wear rates and specific energies of some ceramic, cermet and metallic coatings determined in the Coriolis erosion tester , 1999 .

[8]  R. Wood,et al.  Selection of wear resistant materials for the petrochemical industry , 1992 .

[9]  N. Jayaraman,et al.  Characterisation and wear performance of plasma sprayed WC–Co coatings , 1989 .

[10]  A. Karimi,et al.  Microstructure and hydroabrasive wear behaviour of high velocity oxy-fuel thermally sprayed WCCo(Cr) coatings , 1993 .

[11]  A. Ninham.  The effect of mechanical properties on erosion , 1988 .

[12]  A. Neville,et al.  Assessment of the corrosion rates and mechanisms of a WC–Co–Cr HVOF coating in static and liquid–solid impingement saline environments , 2001 .

[13]  J. E. Ritter.  Erosion of Ceramic Materials , 1992 .

[14]  I. Hutchings,et al.  The rôle of particle properties in the erosion of brittle materials , 1996 .

[15]  I. Finnie.  Erosion of surfaces by solid particles , 1960 .

[16]  S. Wada.  Effects of Hardness and Fracture Toughness of Target Materials and Impact Particles on Erosion of Ceramic Materials , 1992 .

[17]  P. H. Shipway,et al.  Abrasive wear behaviour of conventional and nanocomposite HVOF-sprayed WC–Co coatings , 1999 .

[18]  T. R. Wilshaw,et al.  Quasi-static solid particle damage in brittle solids—I. Observations analysis and implications , 1976 .

[19]  B. Venkataraman,et al.  Effect of grinding on the erosion behaviour of a WC–Co–Cr coating deposited by HVOF and detonation gun spray processes , 2001 .

[20]  P. Griffith,et al.  Erosion of Metallic Plate by Solid Particles Entrained in a Liquid Jet , 1983 .

[21]  C. Allen,et al.  Microstructure/property relationships in the slurry erosion of tungsten carbide–cobalt , 1999 .

[22]  S. Wayne,et al.  Structure/property relationships in sintered and thermally sprayed WC-Co , 1992 .

[23]  B. Mellor,et al.  Fracture toughness and crack morphologies in eroded WC-Co-Cr thermally sprayed coatings , 1998 .

[24]  J. Martín,et al.  Slurry erosion behaviour of thermally sprayed WC-M coatings , 1995 .

[25]  Lin Fuyan,et al.  The effect of impingement angle on slurry erosion , 1991 .

[26]  P. H. Shipway,et al.  Microstructural evolution in thermally sprayed WC-Co coatings: Comparison between nanocomposite and conventional starting powders , 2000 .

[27]  K. Stokes,et al.  The performance of marine coatings and pipe materials under fluid-borne sand erosion , 1998 .