Cyclic plastic strain based damage tolerance for railway axles in China

Abstract Railway axle is one of the most important safety critical components usually operated over a service life of 30 years or more in the order of 109 cyclic loading. Therefore, any derailment caused by fatigue damage should be rigorously inspected, assessed and repaired in both routine and emergence maintenance. By considering the effects of crack closure and load ratio, based on plastic strain energy and modified Rice-Kujawski-Ellyin solution in the tip of a growing fatigue crack under plane stress condition, a new crack closure based fatigue crack growth rate model entitled LowGRO has been proposed in terms of low cycle fatigue behavior and improved threshold stress intensity factor range at different loading ratios. For the railway axle used steel 25CrMo4, 34CrNiMo6 and open-reported structural materials, predicted results of current LowGRO are in good agreement with the experimental data. The LowGRO provides a potential compliment during the damage tolerance design like standard NASGRO equation commonly used for high-speed railway axles.

[1]  Fernand Ellyin,et al.  Crack growth rate under cyclic loading and effect of different singularity fields , 1986 .

[2]  F. Ellyin,et al.  3-D Modelling of Plasticity Induced Fatigue Crack Closure-Effect of Material Constitutive Relations , 2010, CP 2013.

[3]  N. Dowling,et al.  Size effects on the fatigue crack growth rate of Type 304 stainless steel , 1979 .

[4]  Andrew H. Sherry,et al.  COMPENDIUM OF T‐STRESS SOLUTIONS FOR TWO AND THREE DIMENSIONAL CRACKED GEOMETRIES , 1995 .

[5]  Kenji Hirakawa,et al.  Review of the fatigue damage tolerance of high-speed railway axles in Japan , 2011 .

[6]  Daniel Kujawski,et al.  A fatigue crack propagation model , 1984 .

[7]  José Costa,et al.  Low-cycle fatigue behaviour of 34CrNiMo6 high strength steel , 2012 .

[8]  Katrin Mädler,et al.  An experimental approach to determining the residual lifetimes of wheelset axles on a full-scale wheel-rail roller test rig , 2016 .

[9]  Chun‐Sing Lee,et al.  An Improvement on Prediction of Fatigue Crack Growth from Low Cycle Fatigue Properties , 1998 .

[10]  Reinhard Pippan,et al.  Modified NASGRO equation for physically short cracks , 2014 .

[11]  P. C. Paris,et al.  A Critical Analysis of Crack Propagation Laws , 1963 .

[12]  G. Glinka,et al.  A two parameter driving force for fatigue crack growth analysis , 2005 .

[13]  Cheng Yu,et al.  On the fatigue performance of laser hybrid welded high Zn 7000 alloys for next generation railway components , 2016 .

[14]  D. Mowbray,et al.  Relationships Between Low-Cycle Fatigue and Fatigue Crack Growth Rate Properties , 1979 .

[15]  Claude Bathias,et al.  Fatigue of Materials and Structures: Fundamentals , 2013 .

[16]  Kiran Solanki,et al.  Finite element modeling of plasticity-induced crack closure with emphasis on geometry and mesh refinement effects , 2003 .

[17]  K. N. Pandey,et al.  Fatigue crack growth model for constant amplitude loading , 2004 .

[18]  S. Wu,et al.  Structural fatigue crack growth on a representative volume element under cyclic strain behavior , 2015 .

[19]  K. Macdonald,et al.  Fracture and fatigue of welded joints and structures , 2011 .

[20]  S. Beretta,et al.  An approximation for the cyclic state of stress ahead of cracks and its implications under fatigue crack growth , 2011 .

[21]  M. Dankert,et al.  AN ANALYTICAL PROCEDURE FOR PREDICTING OPENING LOADS OF CRACKS AT NOTCHES , 1995 .

[22]  Reinhard Pippan,et al.  Damage tolerance of railway axles – The issue of transferability revisited , 2016 .

[23]  Daniel Kujawski,et al.  A fatigue crack growth model with load ratio effects , 1987 .

[24]  John R. Rice,et al.  Mechanics of Crack Tip Deformation and Extension by Fatigue , 1967 .

[25]  Stefano Beretta,et al.  Probabilistic fatigue assessment for railway axles and derivation of a simple format for damage calculations , 2016 .

[26]  Marco Antonio Meggiolaro,et al.  Singular and non-singular approaches for predicting fatigue crack growth behavior , 2005 .

[27]  Uwe Zerbst,et al.  About the fatigue crack propagation threshold of metals as a design criterion – A review , 2016 .

[28]  Jaap Schijve,et al.  Fatigue of structures and materials , 2001 .

[29]  Uwe Zerbst,et al.  The development of a damage tolerance concept for railway components and its demonstration for a railway axle , 2005 .

[30]  A. Bakker.  Mechanical Behaviour of Materials , 1995 .

[31]  Byong-Whi Lee,et al.  Plastic zone size in fatigue cracking , 1996 .

[32]  Uwe Zerbst,et al.  Safe life and damage tolerance aspects of railway axles – A review , 2013 .

[33]  A. J. Carlsson,et al.  Influence of non-singular stress terms and specimen geometry on small-scale yielding at crack tips in elastic-plastic materials , 1973 .

[34]  L. Cai,et al.  Prediction of fatigue crack growth based on low cycle fatigue properties , 2014 .

[35]  C Boller,et al.  Materials Data for Cyclic Loading , 1990 .

[36]  G. Glinka.  A cumulative model of fatigue crack growth , 1982 .

[37]  F. Ellyin.  Fatigue Damage, Crack Growth and Life Prediction , 1996 .

[38]  S. C. Wu,et al.  Thermal crack growth-based fatigue life prediction due to braking for a high-speed railway brake disc , 2016 .

[39]  E. Wolf.  Fatigue crack closure under cyclic tension , 1970 .

[40]  M. E. Haddad,et al.  Prediction of non propagating cracks , 1979 .

[41]  J. Newman.  A crack opening stress equation for fatigue crack growth , 1984 .