Mechanisms of grain boundary engineering

Abstract This paper reports new data for the analysis of grain boundary misorientation populations and microstructure characteristics in grain boundary engineering (GBE) copper, accompanied by parallel measurements in a non-GBE control specimen of the same material. The GBE processing resulted in a doubling the number fraction of Σ3 boundaries to 41%, accompanied by a 12 times increase in Σ9. The Σ3 population has a convoluted morphology, indicating a range of boundary planes and associated mobilities, and moreover indicating that such Σ3s arise from Σ3 n interactions. Many Σ3s become incorporated into the grain boundary network. Hence, the grain boundary network is modified directly via partial replacement by Σ3s. This is termed the ‘Σ3 regeneration mechanism’. The data from the GBE copper were compared with data previously acquired from GBE brass. The brass has approximately the same number fraction of Σ3s (38%), but a lower number fraction of Σ9s and Σ27s and a markedly different microstructure where twins are not incorporated into the grain boundary network and instead the network is modified indirectly via the modification to the boundary crystallography that results from twinning. This is termed the ‘new twinning’ mechanism. It is suggested that these two mechanisms are general for all GBE metals where the GBE is based on annealing twinning. After the condition of a minimum number fraction (≈20%) of Σ3s is met, the proportion of each mechanism that operates will be governed by processing variables, e.g., cold deformation level and annealing time/temperature.

[1]  L. Clarebrough,et al.  Dissociation of asymmetric ∑9, ∑27a and ∑81d 〈110〉 tilt boundaries , 1984 .

[2]  Valerie Randle,et al.  Twinning-related grain boundary engineering , 2004 .

[3]  W. King,et al.  Analysis of grain boundary networks and their evolution during grain boundary engineering , 2003 .

[4]  M. Finnis,et al.  The influence of grain boundary inclination on the structure and energy of Σ=3 grain boundaries in copper , 1992 .

[5]  W. King,et al.  Toward Optimization of the Grain Boundary Character Distribution in OFE Copper , 1998 .

[6]  H. Davies,et al.  A comparison between three-dimensional and two-dimensional grain boundary plane analysis. , 2002, Ultramicroscopy.

[7]  W. King,et al.  Modifications to the microstructural topology in f.c.c. materials through thermomechanical processing , 2000 .

[8]  J. Lippold,et al.  The effect of annealing twin-generated special grain boundaries on HAZ liquation cracking of nickel-base superalloys , 2003 .

[9]  V. G. Keramidas.  Science and technology of interfaces , 1990 .

[10]  C. Schuh,et al.  Preface to the viewpoint set on grain boundary engineering , 2006 .

[11]  G. Rohrer,et al.  Five-parameter grain boundary distribution in grain boundary engineered brass , 2005 .

[12]  I. Thompson,et al.  On the relationship between grain boundary connectivity, coincident site lattice boundaries, and intergranular stress corrosion cracking , 2004 .

[13]  Mukul Kumar,et al.  Electron Backscatter Diffraction in Materials Science , 2000 .

[14]  Valerie Randle,et al.  Mechanism of twinning-induced grain boundary engineering in low stacking-fault energy materials , 1999 .

[15]  G. Gottstein.  Annealing texture development by multiple twinning in f.c.c. crystals , 1984 .

[16]  P. Lin,et al.  Mitigating intergranular attack and growth in lead-acid battery electrodes for extended cycle and operating life , 1998 .

[17]  P. Lin,et al.  Influence of grain boundary character distribution on sensitization and intergranular corrosion of alloy 600 , 1995 .

[18]  G. Palumbo,et al.  Structure-dependence of intergranular corrosion in high purity nickel , 1990 .

[19]  C. Mcmahon,et al.  The effect of grain-boundary-engineering-type processing on oxygen-induced cracking of IN718 , 2003 .

[20]  P. J. King,et al.  Grain boundary design and control for intergranular stress-corrosion resistance , 1991 .

[21]  H. Davies,et al.  Evolution of microstructure and properties in alpha-brass after iterative processing , 2002 .

[22]  H. Ryoo,et al.  A grain boundary engineering approach to promote special boundaries in Pb-base alloy , 2003 .

[23]  P. King,et al.  On annealing twins and CSL distributions in F.C.C. polycrystals , 1992 .