3D printed oral theophylline doses with innovative 'radiator-like' design: Impact of polyethylene oxide (PEO) molecular weight.
暂无分享,去创建一个
Matthew Peak | Abdullah Isreb | Mohammad Isreb | Mohamed A Alhnan | M. Isreb | A. Isreb | M. Peak | Magdalena Wojsz | Krzysztof Baj | M. Alhnan | K. Baj | M. Wojsz | Abdullah Isreb | Magdalena Wojsz
[1] K. Marra,et al. Polymeric Biomaterials as Tissue Scaffolds , 2015 .
[2] L. Maggi,et al. High molecular weight polyethylene oxides (PEOs) as an alternative to HPMC in controlled release dosage forms. , 2000, International journal of pharmaceutics.
[3] K. Sako,et al. Extended release of a large amount of highly water-soluble diltiazem hydrochloride by utilizing counter polymer in polyethylene oxides (PEO)/polyethylene glycol (PEG) matrix tablets. , 2008, European journal of pharmaceutics and biopharmaceutics : official journal of Arbeitsgemeinschaft fur Pharmazeutische Verfahrenstechnik e.V.
[4] A. Basit,et al. 3D printing of modified-release aminosalicylate (4-ASA and 5-ASA) tablets. , 2015, European journal of pharmaceutics and biopharmaceutics : official journal of Arbeitsgemeinschaft fur Pharmazeutische Verfahrenstechnik e.V.
[5] Feng Zhang,et al. Properties of sustained-release tablets prepared by hot-melt extrusion. , 1999, Pharmaceutical development and technology.
[6] A. Moroni,et al. Application of Poly(oxyethylene) Homopolymers in Sustained Release Solid Formulations , 1995 .
[7] Abdullah Isreb,et al. ‘Temporary Plasticiser’: A novel solution to fabricate 3D printed patient‐centred cardiovascular ‘Polypill’ architectures , 2019, European journal of pharmaceutics and biopharmaceutics : official journal of Arbeitsgemeinschaft fur Pharmazeutische Verfahrenstechnik e.V.
[8] A Apicella,et al. Poly(ethylene oxide) (PEO) and different molecular weight PEO blends monolithic devices for drug release. , 1993, Biomaterials.
[9] K. Wissbrun. Observations on the Melt Rheology of Thermotropic Aromatic Polyesters , 2007 .
[10] A. Peacock,et al. Tensile Properties of Crystalline Polymers: Linear Polyethylene , 1994 .
[11] Sheng Qi,et al. An investigation into the use of polymer blends to improve the printability of and regulate drug release from pharmaceutical solid dispersions prepared via fused deposition modeling (FDM) 3D printing. , 2016, European journal of pharmaceutics and biopharmaceutics : official journal of Arbeitsgemeinschaft fur Pharmazeutische Verfahrenstechnik e.V.
[12] Xinggang Yang,et al. Preparation and investigation of novel gastro-floating tablets with 3D extrusion-based printing. , 2018, International journal of pharmaceutics.
[13] C. Kim. Effects of drug solubility, drug loading, and polymer molecular weight on drug release from Polyox tablets. , 1998, Drug development and industrial pharmacy.
[14] F. Collins,et al. The path to personalized medicine. , 2010, The New England journal of medicine.
[15] M. A. Alhnan,et al. A flexible-dose dispenser for immediate and extended release 3D printed tablets. , 2015, European journal of pharmaceutics and biopharmaceutics : official journal of Arbeitsgemeinschaft fur Pharmazeutische Verfahrenstechnik e.V.
[16] Jukka Rantanen,et al. Modifying release characteristics from 3D printed drug-eluting products. , 2016, European journal of pharmaceutical sciences : official journal of the European Federation for Pharmaceutical Sciences.
[17] R. J. Gaymans,et al. The tensile properties of poly(ethylene oxide)-based segmented block copolymers in the dry and wet state , 2009, Journal of Materials Science.
[18] K. Fukushige,et al. 3D Printing Factors Important for the Fabrication of Polyvinylalcohol Filament-Based Tablets. , 2017, Biological & pharmaceutical bulletin.
[19] M. A. Alhnan,et al. Fabrication of extended-release patient-tailored prednisolone tablets via fused deposition modelling (FDM) 3D printing. , 2015, European journal of pharmaceutical sciences : official journal of the European Federation for Pharmaceutical Sciences.
[20] Peter Timmins,et al. From ‘fixed dose combinations’ to ‘a dynamic dose combiner’: 3D printed bi‐layer antihypertensive tablets , 2018, European journal of pharmaceutical sciences : official journal of the European Federation for Pharmaceutical Sciences.
[21] Touraj Ehtezazi,et al. The Application of 3D Printing in the Formulation of Multilayered Fast Dissolving Oral Films. , 2017, Journal of pharmaceutical sciences.
[22] Evert Fuenmayor,et al. Material Considerations for Fused-Filament Fabrication of Solid Dosage Forms , 2018, Pharmaceutics.
[23] Simon Gaisford,et al. 3D printed medicines: A new branch of digital healthcare , 2018, International journal of pharmaceutics.
[24] C. Hock,et al. Melting-point depression by insoluble impurities: a finite size effect. , 2008, Physical review letters.
[25] C. Booth,et al. Thermodynamic melting point of poly(ethylene oxide) , 1970 .
[26] Hugh Smyth,et al. 3D Printing technologies for drug delivery: a review , 2016, Drug development and industrial pharmacy.
[27] Niklas Sandler,et al. 3D printed drug delivery devices: perspectives and technical challenges , 2017, Expert review of medical devices.
[28] Basel Arafat,et al. Tailored on demand anti‐coagulant dosing: An in vitro and in vivo evaluation of 3D printed purpose‐designed oral dosage forms , 2018, European journal of pharmaceutics and biopharmaceutics : official journal of Arbeitsgemeinschaft fur Pharmazeutische Verfahrenstechnik e.V.
[29] J. Grotenhuis,et al. Safety and efficacy of a novel polyethylene glycol hydrogel sealant for watertight dural repair. , 2007, Journal of neurosurgery.
[30] Waqar Ahmed,et al. Adaptation of pharmaceutical excipients to FDM 3D printing for the fabrication of patient-tailored immediate release tablets. , 2016, International journal of pharmaceutics.
[31] P. Belton,et al. Development of a Simple Mechanical Screening Method for Predicting the Feedability of a Pharmaceutical FDM 3D Printing Filament , 2018, Pharmaceutical Research.
[32] Feng Zhang,et al. Stability of polyethylene oxide in matrix tablets prepared by hot-melt extrusion. , 2002, Biomaterials.
[33] V. Mironov,et al. Photopolymerization-based additive manufacturing for the development of 3D porous scaffolds , 2014 .
[34] Carolyn L. Mazzitelli,et al. Polyethylene glycols in oral and parenteral formulations--A critical review. , 2015, International journal of pharmaceutics.
[35] Waqar Ahmed,et al. Emergence of 3D Printed Dosage Forms: Opportunities and Challenges , 2016, Pharmaceutical Research.