Boundary characterization of MEMS structures through electro-mechanical testing

Micro-electro-mechanical-systems (MEMS) are coupled electro-mechanical microsystems used in many different sensing and actuation applications. The mechanical characteristics of the microsystem depend in large part to the choice of material and microfabrication process. In microsystems where there are suspended structures, as in the case of atomic force microscope (AFM) microcantilever probes, the boundary supports are uniquely defined by the microfabrication process implemented. In practice, AFM microcantilever probes suffer from large variations in natural frequencies due to the inherent microfabrication limitations, such as, material non-uniformity, geometrical non-uniformity and non-classical boundary support conditions. Out of these influences, non-classical boundary support conditions are difficult to estimate and are also very important for design and modeling considerations. Hence, this paper presents a testing method in which most of the influences were quantified or made variant while the support condition was kept invariant. This approach will help to identify the influence of microfabrication to the support boundary condition. This paper presents the results on the characterization of non-classical support boundary conditions of microcantilevers through electro-mechanical testing. A laser based non-contact optical testing approach is employed for the dynamic testing of the microstructure. The theoretical formulation is based on the Rayleigh-Ritz energy method using boundary characteristic orthogonal polynomials.

[1]  Muthukumaran Packirisamy,et al.  Experimental investigation on the dynamics of MEMS structures , 2004, SPIE Photonics Europe.

[2]  Ion Stiharu,et al.  BOUNDARY CONDITIONING TECHNIQUE FOR STRUCTURAL TUNING , 1999 .

[3]  A. Nayfeh,et al.  Modeling and design of variable-geometry electrostatic microactuators , 2005 .

[4]  Long Jiang,et al.  A novel microgravimetric DNA sensor with high sensitivity. , 2003, Biochemical and biophysical research communications.

[5]  H. Fujita,et al.  A 5-V operated MEMS variable optical attenuator by SOI bulk micromachining , 2004, IEEE Journal of Selected Topics in Quantum Electronics.

[7]  Niels Leergaard Pedersen,et al.  DESIGN OF CANTILEVER PROBES FOR ATOMIC FORCE MICROSCOPY (AFM) , 2000 .

[8]  R. Bhat.  NATURE OF STATIONARITY OF THE NATURAL FREQUENCIES AT THE NATURAL MODES IN THE RAYLEIGH–RITZ METHOD , 1997 .

[9]  Bernd Michel,et al.  Vibration measurement of microstructures by means of laser-optical modal analysis , 1999, Industrial Lasers and Inspection.

[10]  Muthukumaran Packirisamy,et al.  Optical MEMS-based bimorph for thermal sensing , 2004, Photonics North.

[11]  B. Harnisch,et al.  Micro Spectrometer and MEMS for Space , 2002 .

[12]  G. Kovacs,et al.  Bulk micromachining of silicon , 1998, Proc. IEEE.

[13]  Muthukumaran Packirisamy,et al.  Thermo-electrical influence on static and dynamic behaviour of cantilever type silicon waveguide , 2005, Photonics North.

[14]  E. Ollier.  Optical MEMS devices based on moving waveguides , 2002 .

[15]  Ali H. Nayfeh,et al.  Characterization of the mechanical behavior of an electrically actuated microbeam , 2002 .

[16]  M. Packirisamy,et al.  An improved method for predicting microfabrication influence in atomic force microscopy performances , 2004 .

[17]  M. Grattarola,et al.  Micromechanical cantilever-based biosensors , 2001 .

[18]  I. Stiharu,et al.  Influence of micromachining on dynamic behaviour of mems structures , 2005, Canadian Journal of Electrical and Computer Engineering.

[19]  N. D. Rooij,et al.  Micromachined atomic force microprobe with integrated capacitive read-out , 1992 .

[20]  Muthukumaran Packirisamy,et al.  Boundary characterization of microstructures through thermo-mechanical testing , 2006 .

[21]  B. Paden,et al.  MEMS resonators that are robust to process-induced feature width variations , 2002 .

[22]  R. Bhat.  Natural frequencies of rectangular plates using characteristic orthogonal polynomials in rayleigh-ritz method , 1986 .

[23]  G. Delapierre.  Micro-machining: A survey of the most commonly used processes , 1989 .

[24]  Vinayak P. Dravid,et al.  Microcantilever resonance-based DNA detection with nanoparticle probes , 2003 .

[25]  S. Senturia,et al.  M-TEST: A test chip for MEMS material property measurement using electrostatically actuated test structures , 1997 .

[26]  Mohd P. Omar,et al.  Theoretical modeling of boundary conditions in microfabricated beams , 1991, [1991] Proceedings. IEEE Micro Electro Mechanical Systems.