Quantitative Study of Shrinkage and Warpage Behavior for Microcellular and Conventional Injection Molding

This research investigated the effects of processing conditions on the shrinkage and warpage (S&W) behavior of a box-shaped, polypropylene part using conventional and microcellular injection molding. Two sets of 26-1 fractional factorial design of experiments (DOE) were employed to perform the experiments and proper statistical theory was used to analyze the data. After the injection molding process reached steady state, molded samples were collected and measured using an optical coordinate measuring machine (OCMM), which had been evaluated using a proper R&R (repeatability and reproducibility) measurement study. By analyzing the statistically significant main and two-factor interaction effects, the results show that the supercritical fluid (SCF) content (nitrogen in this case, in terms of SCF dosage time) and the injection speed affect the S&W of microcellular injection molded parts the most, whereas pack/hold pressure and pack/hold time have the most significant effect on the S&W of conventional injection molded parts. Also, this study quantitatively showed that, within the processing range studied, a reduction in the S&W could be achieved with the microcellular injection molding process. POLYM. ENG. SCI., 45:1408–1418, 2005. © 2005 Society of Plastics Engineers

[1]  J. Michael Brick.  Evaluating the Measurement Process , 1989 .

[2]  L. Turng,et al.  Development of a Hybrid Solid-Microcellular Co-injection Molding Process , 2004 .

[3]  Chul B. Park,et al.  A study of cell nucleation in the extrusion of polypropylene foams , 1997 .

[4]  Zhiyi Zhang,et al.  Anin situ study of plasticization of polymers by high-pressure gases , 1998 .

[5]  J. R. Royer,et al.  High-pressure rheology of polystyrene melts plasticized with CO2: Experimental measurement and predictive scaling relationships , 2000 .

[6]  L. Turng,et al.  Microstructure and crystallography in microcellular injection-molded polyamide-6 nanocomposite and neat resin , 2005 .

[7]  Chul B. Park,et al.  Processing and characterization of microcellular foamed high-density polythylene/isotactic polypropylene blends , 1998 .

[8]  N. Suh,et al.  The viscoelastic behavior of microcellular plastics with varying cell size , 1995 .

[9]  C. Manke,et al.  Effects of Dissolved Gas on Viscoelastic Scaling and Glass Transition Temperature of Polystyrene Melts , 2001, Industrial & Engineering Chemistry Research.

[10]  L. Turng,et al.  Cell Development in Microcellular Injection Molded Polyamide-6 Nanocomposite and Neat Resin , 2004 .

[11]  C. Manke,et al.  Rheology of molten polystyrene with dissolved supercritical and near‐critical gases , 1999 .

[12]  P. Kruus,et al.  High-pressure calorimetric study of plasticization of poly(methyl methacrylate) by methane, ethylene, and carbon dioxide , 1996 .

[13]  H. H. Chiang,et al.  Postmolding and load‐induced deformation analysis of plastic parts in the injection molding process , 1991 .

[14]  L. Turng,et al.  Study of injection molded microcellular polyamide-6 nanocomposites , 2004 .

[15]  L. Turng,et al.  Effects of nano-fillers and process conditions on the microstructure and mechanical properties of microcellular injection molded polyamide nanocomposites , 2003 .

[16]  Karl A. Seeler,et al.  Tension-Tension Fatigue of Microcellular Polycarbonate: Initial Results , 1993 .