The flow downstream of a bifurcation of a flow channel for uniform flow distribution via cascade flow channel bifurcations

Abstract Uniform flow distribution is an important and fundamental issue to miscellaneous devices. The present work studied the details of flow in a channel with a fundamental structure—a symmetric bifurcation of one flow channel into two sub-channels. The structure is designated to split one flow into two streams of even flow rate. Key geometric design factors of the flow channel are investigated regarding the effect to the development of a symmetric velocity profile after the flow channel bifurcation, as the symmetric velocity profile is critical to the even split of the flow into two streams in the next stage of flow channel bifurcation. The study is based on both two-dimensional and three-dimensional CFD analyses. Both laminar and turbulent flows are investigated. Commercial CFD software ANSYS FLUENT® was used. The numerical treatment of convection terms in governing equations was based on the QUICK scheme, and the SIMPLE algorithm was used to treat the coupling of pressure and velocity fields. The obtained results are of great significance to the design of flow distributors using cascade flow channel bifurcations.

[1]  H. Martin,et al.  Flow distribution and pressure drop in plate heat exchangers—II Z-type arrangement , 1984 .

[2]  Marek Pronobis,et al.  Influence of non-uniform flow distribution on overall heat transfer in convective bundle of circulating fluidized bed boiler , 2005 .

[3]  Chin‐Hsiang Cheng,et al.  An inverse geometry design problem for optimization of single serpentine flow field of PEM fuel cell , 2010 .

[4]  L. Burmeister.  Convective heat transfer , 1983 .

[5]  Young I. Cho,et al.  The effect of header shapes on the flow distribution in a manifold for electronic packaging applications , 1995 .

[6]  Andreas Richter,et al.  Flow distribution in solar collectors with laminar flow conditions , 2002 .

[7]  Sehyun Shin,et al.  The effect of area ratio on the flow distribution in liquid cooling module manifolds for electronic packaging , 1993 .

[8]  Jon T. Van Lew,et al.  Experimental study of the flow distribution uniformity in flow distributors having novel flow channel bifurcation structures , 2012 .

[9]  Sehyun Shin,et al.  The effects of the Reynolds number and width ratio on the flow distribution in manifolds of liquid cooling modules for electronic packaging , 1993 .

[10]  C. Baxevanou,et al.  Validation of Numerical Schemes and Turbulence Models Combinations for Transient Flow Around Airfoil , 2008 .

[11]  A. Bejan.  Advanced Engineering Thermodynamics , 1988 .

[12]  B. A. Kader.  Temperature and concentration profiles in fully turbulent boundary layers , 1981 .

[13]  Sreenivas Jayanti,et al.  A hydrodynamic network model for interdigitated flow fields , 2009 .

[14]  Junye Wang,et al.  Pressure drop and flow distribution in parallel-channel configurations of fuel cells: U-type arrangement , 2008 .

[15]  Biao Zhou,et al.  Liquid water transport in straight micro-parallel-channels with manifolds for PEM fuel cell cathode , 2006 .

[16]  Moses O. Tadé,et al.  A CFD-based model of a planar SOFC for anode flow field design , 2009 .

[17]  Dana Rusch,et al.  Turbulence model validation for fire simulation by CFD and experimental investigation of a hot jet in crossflow , 2008 .

[18]  H. D. Zughbi,et al.  Simulation of Flow Distribution in Radial Flow Reactors , 2006 .

[19]  Yanzhong Li,et al.  An experimental and numerical investigation of flow patterns in the entrance of plate-fin heat exchanger , 2006 .

[20]  Gregory A. Kiker,et al.  The effect of irrigation uniformity on irrigation water requirements , 2002 .

[21]  Peiwen Li,et al.  Even distribution/dividing of single-phase fluids by symmetric bifurcation of flow channels , 2013 .

[22]  Peiwen Li,et al.  MAINTAINING EQUAL OPERATING CONDITIONS FOR ALL CELLS IN A FUEL CELL STACK USING AN EXTERNAL FLOW DISTRIBUTOR , 2013 .

[23]  Junye Wang,et al.  A theoretical model of uniform flow distribution for the admission of high-energy fluids to a surface steam condenser , 2001 .

[24]  R. Kee,et al.  A generalized model of the flow distribution in channel networks of planar fuel cells , 2002 .

[25]  Adrian Bejan,et al.  Vascular structures with flow uniformity and small resistance , 2009 .

[26]  Roger R. Schmidt,et al.  Airflow Uniformity Through Perforated Tiles in a Raised-Floor Data Center , 2005 .

[27]  Xianguo Li,et al.  Review of bipolar plates in PEM fuel cells: Flow-field designs , 2005 .