Elastic–plastic modeling of heat-treated bimorph micro-cantilevers

This paper models the residual stress distributions within micro-fabricated bimorph cantilevers of varying thickness. A contact model is introduced to calculate the influence of contact on the residual stress following a heat treatment process. An analytical modeling approach is adopted to characterize bimorph cantilevers composed of thin Au films deposited on thick poly-silicon or silicon-dioxide beams. A thermal elastic–plastic finite element model (FEM) is utilized to calculate the residual stress distribution across the cantilever cross-section and to determine the beam tip deflection following heat treatment. The influences of the beam material and thickness on the residual stress distribution and tip deflections are thoroughly investigated. The numerical results indicate that a larger beam thickness leads to a greater residual stress difference at the interface between the beam and the film. The residual stress established in the poly-silicon cantilever is greater than that induced in the silicon-dioxide cantilever. The results confirm the ability of the developed thermal elastic–plastic finite element contact model to predict the residual stress distributions within micro-fabricated cantilever structures with high accuracy. As such, the proposed model makes a valuable contribution to the development of micro-cantilevers for sensor and actuator applications.

[1]  Paul A. Kohl,et al.  Stresses in thin film metallization , 1997 .

[2]  Alan G. R. Evans,et al.  Characterization of a highly sensitive ultra-thin piezoresistive silicon cantilever probe and its application in gas flow velocity sensing , 2002 .

[3]  P. Flinn,et al.  Measurement and Interpretation of stress in aluminum-based metallization as a function of thermal history , 1987, IEEE Transactions on Electron Devices.

[4]  Development of a novel self-sensitive atomic force microscope for nondestructive measurement of micro vertical surfaces , 2004 .

[5]  Julie Gold,et al.  Microfabricated force-sensitive elastic substrates for investigation of mechanical cell–substrate interactions , 2003 .

[6]  V. M. Lubecke,et al.  Self-assembling MEMS variable and fixed RF inductors , 2001 .

[7]  Christian Rembe,et al.  Micromirrors for Adaptive-Optics Arrays , 2001 .

[8]  Gwo-Bin Lee,et al.  Micromachine-based humidity sensors with integrated temperature sensors for signal drift compensation , 2003 .

[9]  W. Hsu,et al.  An electro-thermally driven microactuator with two dimensional motion , 2002 .

[10]  J. Frühauf,et al.  Silicon as a plastic material , 1999 .

[11]  Lutz Doering,et al.  Piezoresistive cantilever as portable micro force calibration standard , 2003 .

[12]  J. Söderkvist,et al.  High-sensitivity surface micromachined structures for internal stress and stress gradient evaluation , 1997 .

[13]  Richard B. Fair,et al.  Mechanical Property Measurement of Thin-film Gold Using Thermally Actuated Bimetallic Cantilever Beams , 2001 .

[14]  Young-Pil Park,et al.  Swing-arm-type PZT dual actuator with fast seeking for optical disk drive , 2002 .

[15]  Neville Ka-shek Lee,et al.  Numerical simulation of a polysilicon thermal flexure actuator , 2002 .

[16]  Piezoelectric thin films formed by MOD on cantilever beams for micro sensors and actuators , 2004 .

[17]  W. Peng,et al.  Transient analysis of sliding contact of layered elastic/plastic solids with rough surfaces , 2003 .

[18]  Paul Gonnard,et al.  Modelling of a cantilever non-symmetric piezoelectric bimorph , 2003 .

[19]  W. Fang.  Determination of the elastic modulus of thin film materials using self-deformed micromachined cantilevers , 1999 .