Experiments and Modelling of Producer Gas Based Reciprocating Engines

A 20 kW reciprocating engine is operated using producer gas derived from a modern open top downdraft re-burn biomass gasifier that has been evaluated by rigorous laboratory performance testing over several hundred hours. The engine is operated at varying compression ratio (CR) from 11.5 to 17.0 and ignition timings from 30 to 6° before Top Centre (TC). The engine – alternator system is characterised for its performance by the simultaneous measurement of gas and airflow rates, gas composition (on-line), emission levels and power delivered. It is also instrumented to obtain the in-cylinder behaviour in the form of pressure-crank angle (p – θ) diagram to assess the thermodynamic behaviour of the engine. Three-dimensional (3-D) simulation of the flow field in the combustion chamber (involving piston-bowl arrangement) through the cycle up to the start of the combustion is used to obtain inputs on the turbulence intensity (u′) and length scale (l T ) for the modelling of the flame propagation process in a zero-dimensional model (0-D) designed to predict the p – θ curve. The flame propagation and heat release processes make use of eddy entrainment and laminar burn-up model. The data on u′ extracted from the 3-D flow calculations match reasonably well with experiments till compression stroke but are in contradiction with trends close to TC. This is reasoned to be due to limitation of the k-e model to capture transient effects due to reverse squish phenomenon. The 0-D model took into account the experimental behaviour of the u′ in the post-TC period to attempt to match the observed p – θ data over a range of CRs and ignition timing advances. While these predictions match well with the experimental data at advanced ignition timing at both higher and lower CRs, the peak pressure is under-predicted at lower ignition advances; reason are traced to increase in flame area and propagation speed due to reverse squish effect. When these are accounted in the model, the p – θ curves are predicted better.© 2002 ASME

[1]  R. Reitz,et al.  Turbulence Modeling of Internal Combustion Engines Using RNG κ-ε Models , 1995 .

[2]  Andrea Catania,et al.  Speed Dependence of Turbulence Properties in a High-Squish Automotive Engine Combustion System , 1996 .

[3]  P. Paul,et al.  Biomass derived producer gas as a reciprocating engine fuel—an experimental analysis , 2001 .

[4]  Gautam Kalghatgi,et al.  Early flame development in a spark-ignition engine , 1985 .

[5]  U. Shrinivasa,et al.  Open-top wood gasifiers , 1993 .

[6]  Kazushi Nishimoto,et al.  Turbulence intensity and spatial integral scale during compression and expansion strokes in a four-cycle reciprocating engine , 1987 .

[7]  J. Keck.  TURBULENT FLAME STRUCTURE AND SPEED IN SPARK-IGNITION ENGINES , 1982 .

[8]  Philip Jones,et al.  Full Cycle Computational Fluid Dynamics Calculations in a Motored Four Valve Pent Roof Combustion Chamber and Comparison with Experiment , 1995 .

[9]  B. Khalighi,et al.  Particle Image Velocimetry Measurements in a High-Swirl Engine Used for Evaluation of Computational Fluid Dynamics Calculations , 1995 .

[10]  C R Stone,et al.  Measurements and Modelling of a Lean Burn Gas Engine , 1996 .

[11]  Fred Thiele,et al.  Threedimensional Computations for Flowfields in DI Piston Bowls , 1986 .

[12]  M. Jennings.  Multi-Dimensional Modeling of Turbulent Premixed Charge Combustion , 1992 .

[13]  Bruno Dillies,et al.  Engine Flow Calculations Using a Reynolds Stress Model in the Kiva-II Code , 1996 .

[14]  F. E. Corcione,et al.  Analysis of in-cylinder flow processes by LDA. [Laser Doppler Anemometry] , 1994 .

[15]  J. C. Dent,et al.  Turbulent Air Flow in the Combustion Bowl of a D. I. Diesel Engine and Its Effect on Engine Performance , 1979 .

[16]  P. Paul,et al.  Wood-char gasification: Experiments and analysis on single particles and packed beds , 1998 .

[17]  David R. Lancaster,et al.  EFFECTS OF ENGINE VARIABLES ON TURBULENCE IN A SPARK- IGNITION ENGINE , 1976 .

[18]  Tomio Obokata,et al.  Gas Velocity Measurements of a Motored and Firing Engine by Laser Anemometry , 1979 .

[19]  John B. Heywood,et al.  Internal combustion engine fundamentals , 1988 .