Composite skin-stiffener debond analyses using fracture mechanics approach with shell elements

Abstract Fracture mechanics analyses of composite skin-stiffener debond configurations using shell elements are presented. Two types of debond configurations are studied: a flange skin strip debond configuration and a skin-stiffener debond configuration. The flange-skin strip configuration examines debond growth perpendicular to the stiffener while the skin-stiffener configuration examines debond growth parallel to the stiffener. Four-node and 9-node shell elements are used to model both debond configurations. The stiffener flange and skin are modeled as two different layers of elements whose translational degrees-of-freedom, in the bonded portion, of the corresponding flange and skin nodes are constrained to be identical. Strain energy release rate formulae are presented for both 4-node and 9-node element models based on the virtual crack closure technique (VCCT). In addition, average values of the strain energy release rates are calculated using a gradient method. The VCCT formulae and the gradient method are used to compute the strain energy release rates ( G -values) for both debond configurations. The G -values predicted by these methods are compared with those predicted by plane-strain and 3D finite element analyses. Excellent correlation is obtained among all the analysis results, thus helping to validate the VCCT formulae derived for the 4- and 9-node shell elements.

[1]  John D. Whitcomb,et al.  Strain-energy release rate analysis of a laminate with a postbuckled delamination , 1987 .

[2]  David Cohen,et al.  Calculation of stresses and forces between the skin and stiffener in composite panels , 1987 .

[3]  E. F. Bruhn,et al.  Analysis and Design of Flight Vehicle Structures , 1973 .

[4]  Kunigal N. Shivakumar,et al.  Three-dimensional elastic analysis of a composite double cantilever beam specimen , 1988 .

[5]  K. Park,et al.  A Curved C0 Shell Element Based on Assumed Natural-Coordinate Strains , 1986 .

[6]  M. Kanninen,et al.  A finite element calculation of stress intensity factors by a modified crack closure integral , 1977 .

[7]  T. Krishnamurthy,et al.  Fracture mechanics analyses for skin-stiffener debonding , 1996 .

[8]  James H. Starnes,et al.  Stiffener-skin interactions in pressure-loaded composite panels , 1990 .

[9]  S. Biggers,et al.  Skin-stiffener interface stresses in composite stiffened panels , 1984 .

[10]  J. Newman,et al.  Three-dimensional finite-element analysis of chevron-notched fracture specimens , 1984 .

[11]  A.S.D. Wang,et al.  Initiation and Growth of Transverse Cracks and Edge Delamination in Composite Laminates Part 1. An Energy Method , 1980 .

[12]  T. O'Brien.  Characterization of delamination onset and growth in a composite laminate , 1982 .

[13]  J. Rice,et al.  Elementary engineering fracture mechanics , 1974 .

[14]  James H. Starnes,et al.  Postbuckling behavior of selected flat stiffened graphite-epoxy panels loaded in compression , 1982 .

[15]  John D. Whitcomb,et al.  Instability-related delamination growth of embedded and edge delaminations. Ph.D. Thesis - Virginia Polytechnic Inst. and State Univ. , 1988 .

[16]  B. Sankar,et al.  A Plate Finite Element for Modeling Delaminations , 1993 .

[17]  I. Raju,et al.  Residual thermal and moisture influences on the strain energy release rate analysis of edge delamination , 1986 .

[18]  I. S. Raju,et al.  Computation of strain energy release rates for skin-stiffener debonds modeled with plate elements , 1993 .

[19]  I. Raju.  Calculation of strain-energy release rates with higher order and singular finite elements , 1987 .