Nafion–TiO2 composite DMFC membranes: physico-chemical properties of the filler versus electrochemical performance

TiO2 nanometric powders were prepared via a sol–gel procedure and calcined at various temperatures to obtain different surface and bulk properties. The calcined powders were used as fillers in composite Nafion membranes for application in high temperature direct methanol fuel cells (DMFCs). The powder physico-chemical properties were investigated by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and pH measurements. The observed characteristics were correlated to the DMFC electrochemical behaviour. Analysis of the high temperature conductivity and DMFC performance reveals a significant influence of the surface characteristics of the ceramic oxide, such as oxygen functional groups and surface area, on the membrane electrochemical behaviour. A maximum DMFC power density of 350 mW cm −2 was achieved under oxygen feed at 145 ◦ C in a pressurized DMFC (2.5 bar, anode and cathode) equipped with TiO2 nano-particles based composite membranes.

[1]  V. Antonucci,et al.  Hybrid Nafion-silica membranes doped with heteropolyacids for application in direct methanol fuel cells , 2001 .

[2]  K. Kreuer.  On the development of proton conducting polymer membranes for hydrogen and methanol fuel cells , 2001 .

[3]  Antonino S. Aricò,et al.  Surface properties of inorganic fillers for application in composite membranes-direct methanol fuel cells , 2004 .

[4]  Shimshon Gottesfeld,et al.  The Water Content Dependence of Electro-Osmotic Drag in Proton-Conducting Polymer Electrolytes , 1995 .

[5]  Shimshon Gottesfeld,et al.  High performance direct methanol polymer electrolyte fuel cells , 1996 .

[6]  V. Antonucci,et al.  Influence of the acid-base characteristics of inorganic fillers on the high temperature performance of composite membranes in direct methanol fuel cells , 2003 .

[7]  R. Savinell,et al.  Evaluation of a Sol-Gel Derived Nafion/Silica Hybrid Membrane for Proton Electrolyte Membrane Fuel Cell Applications: I. Proton Conductivity and Water Content , 2001 .

[8]  S. Wasmus,et al.  Methanol oxidation and direct methanol fuel cells: a selective review 1 In honour of Professor W. Vi , 1999 .

[9]  V. Antonucci,et al.  Effect of PtRu alloy composition on high-temperature methanol electro-oxidation , 2002 .

[10]  S. Srinivasan,et al.  Composite Nafion/Zirconium Phosphate Membranes for Direct Methanol Fuel Cell Operation at High Temperature , 2001 .

[11]  Hiroyuki Uchida,et al.  Self‐Humidifying Polymer Electrolyte Membranes for Fuel Cells , 1996 .

[12]  U. Stimming,et al.  Catalysts for Direct Methanol Fuel Cells , 2002 .

[13]  G. G. Stokes.  "J." , 1890, The New Yale Book of Quotations.

[14]  Andrew B. Bocarsly,et al.  Silicon Oxide Nafion Composite Membranes for Proton-Exchange Membrane Fuel Cell Operation at 80-140°C , 2002 .

[15]  Giuliano Martinelli,et al.  Sol-Gel Processed TiO2-Based Nano-Sized Powders for Use in Thick-Film Gas Sensors for Atmospheric Pollutant Monitoring , 2001 .

[16]  V. Antonucci,et al.  FTIR spectroscopic investigation of inorganic fillers for composite DMFC membranes , 2003 .

[17]  Antonino S. Aricò,et al.  Comparison of Ethanol and Methanol Oxidation in a Liquid‐Feed Solid Polymer Electrolyte Fuel Cell at High Temperature , 1999 .

[18]  Antonino S. Aricò,et al.  DMFCs: From Fundamental Aspects to Technology Development , 2001 .