An efficient photoresist development simulator based on cellular automata with experimental verification

An efficient and practical photoresist development simulator based on cellular automata is presented. Image reversal and chemical amplification processes are also simulated using this simulator. To verify the simulator, a series of experiments have been designed and performed using the Shipley SNR-248 negative resist, a stepper, and a deep ultraviolet source at 248 nm. Experiments were performed for periodic and isolated lines with pitches 300, 400, 500, and 1000 nm, for exposure energy doses of 11, 13, 17, and 23 mJ/cm/sup 2/, and with developer temperatures of 0, 20, and 80/spl deg/C. In all cases, the simulator results were found to be in very good agreement with the corresponding experimental results. The simulator has also successfully reproduced the incomplete opening effect observed in the case of close-spaced parallel lines.

[1]  Masato Fujinaga,et al.  3-D topography simulator (3-D MULSS) based on a physical description of material topography , 1997 .

[2]  P. S. Hauge,et al.  Characterization of positive photoresist , 1975, IEEE Transactions on Electron Devices.

[3]  E. W. Scheckler,et al.  An efficient volume-removal algorithm for practical three-dimensional lithography simulation with experimental verification , 1993, IEEE Trans. Comput. Aided Des. Integr. Circuits Syst..

[4]  A. M. Bruning,et al.  Simulation of electrical tree growth in solid insulating materials , 1998 .

[5]  James W. Thackeray,et al.  Deep UV ANR Photoresists For 248 nm Excimer Laser Photolithography , 1989, Advanced Lithography.

[6]  I. Karafyllidis.  Simulation of the negative chemical amplification deep-ultraviolet process in integrated circuit fabrication , 1997 .

[7]  G. Vichniac.  Simulating physics with cellular automata , 1984 .

[8]  Andrew R. Neureuther,et al.  Negative resist corner rounding. Envelope volume modeling , 1996 .

[9]  A. Neureuther,et al.  Modeling projection printing of positive photoresists , 1975, IEEE Transactions on Electron Devices.

[10]  Koelman.  Cellular-automaton-based simulation of 2D polymer dynamics. , 1990, Physical review letters.

[11]  Stephen Wolfram,et al.  Cellular Automata And Complexity , 1994 .

[12]  Ioannis G. Karafyllidis,et al.  Dependence of developed negative resist profiles on exposure energy dose: experiment, modeling, and simulation , 1998 .

[13]  D. J. Matzke,et al.  Impact of locality and dimensionality limits on architectural trends , 1994, Proceedings Workshop on Physics and Computation. PhysComp '94.

[14]  Q. Leonard,et al.  An optimization design method for chemically amplified resist process control , 1994 .

[15]  John von Neumann,et al.  Theory Of Self Reproducing Automata , 1967 .

[16]  Andrew R. Neureuther,et al.  Algorithms for simulation of three-dimensional etching , 1994, IEEE Trans. Comput. Aided Des. Integr. Circuits Syst..

[17]  Ioannis G. Karafyllidis,et al.  Simulation of deposition-topography granular distortion for TCAD , 1998 .

[18]  Siegfried Selberherr,et al.  Algorithms and models for cellular based topography simulation , 1995, IEEE Trans. Comput. Aided Des. Integr. Circuits Syst..

[19]  M. Gerhardt,et al.  A cellular automaton describing the formation of spatially ordered structures in chemical systems , 1989 .

[20]  G. Maier.  Polymers for microelectronics , 2001 .

[21]  Theodore Davidson,et al.  Polymers in Electronics , 1984 .

[22]  Andrew R. Neureuther,et al.  Line‐Profile resist development simulation techniques , 1977 .

[23]  Ioannis G. Karafyllidis,et al.  Negative resist profiles of close-spaced parallel and isolated lines: experiment, modelling and simulation , 1999 .

[24]  E.T.L. Omtzigt,et al.  Computational spacetimes , 1994, Proceedings Workshop on Physics and Computation. PhysComp '94.

[25]  Tommaso Toffoli,et al.  Cellular Automata as an Alternative to (Rather than an Approximation of) Differential Equations in M , 1984 .

[26]  Ioannis G. Karafyllidis,et al.  Simulation of two-dimensional photoresist etching process in integrated circuit fabrication using cellular automata , 1995 .

[27]  Andrew R. Neureuther,et al.  Models and algorithms for three-dimensional topography simulation with SAMPLE-3D , 1994, IEEE Trans. Comput. Aided Des. Integr. Circuits Syst..

[28]  Paul Isaac Hagouel,et al.  X-ray lithographic fabrication of blazed diffraction gratings , 1976 .

[29]  Rocco Rongo,et al.  A parallel cellular tool for interactive modeling and simulation , 1996 .

[30]  Ken A. Hawick,et al.  Scientific modeling with massively parallel SIMD computers , 1991, Proc. IEEE.

[31]  Rene Vervoordeldonk,et al.  A Quantitative Assessment Of Image Reversal, A Candidate For A Submicron Process With Improved Linewidth Control , 1986, Advanced Lithography.

[32]  W. Arden,et al.  Image reversal of positive photoresist: Characterization and modeling , 1985, IEEE Transactions on Electron Devices.

[33]  Ioannis G. Karafyllidis,et al.  Simulation of the image reversal submicron process in integrated circuit fabrication , 1996 .

[34]  Paul Isaac Hagouel,et al.  Developer temperature effect on negative deep ultraviolet resists: Characterization, modeling, and simulation , 1997 .

[35]  Ioannis G. Karafyllidis,et al.  Negative resist profiles in 248 nm photolithography: experiment, modelling and simulation , 1998 .