Performance evaluation of Ti–6Al–4V grinding using chip formation and coefficient of friction under the influence of nanofluids

Abstract Nanofluid, fluid suspensions of nanometer sized particles are revolutionizing the field of heat transfer area. Addition of nano-particles to the base fluid also alters the lubricating properties by reducing the friction. In grinding process, friction between the abrasive grains and the workpiece is a key issue governing the main grinding output. It has a direct influence on grinding force, power, specific energy and wheel wear. Moreover, high friction force increases the heat generation and lead to thermal damage in the surface layer of the ground work. Hence, any effort towards the friction control will enhance the component quality significantly. In this study, nanofluid as metal working fluid (MWF) is made by adding 0.05, 0.1, 0.5 and 1% volume concentration of Al2O3 and CuO nano-particles to the water during the surface grinding of Ti–6Al–4V in minimum quantity lubrication (MQL) mode. Surface integrity of ground surface, morphology of the wheel, and chip formation characteristics are studied using surface profilometer, scanning electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS) and stereo zoom microscopy (SZM). Coefficient of friction was estimated On-Machine using the measured forces. The results showed that the type of nanoparticle and its concentration in base fluid and the MQL flow rate play a significant role in reducing friction. Application of nanofluid leads to the reduction of tangential forces and grinding zone temperature. The cooling effect is also evident from the short C-type chip formation. MQL application with Al2O3 nanofluid helps in effective flushing of chip material from the grinding zone, thereby solving the main problem during the grinding of Ti–6Al–4V.

[1]  Zhixiong Zhou,et al.  The tribological properties of nanofluid used in minimum quantity lubrication grinding , 2014 .

[2]  S. Chandrasekar,et al.  Paper VI (iv) Sliding Microindentation Wear Particles: Spheres in Grinding Swarf , 1992 .

[3]  B. K. Vinayagam,et al.  Fractal dimensional surface analysis of AISI D2 Tool steel material with nanofluids in grinding process using atomic force microscopy , 2011 .

[4]  C. A. van Luttervelt,et al.  Recent Developments in Chip Control Research and Applications , 1993 .

[5]  Kamlakar P Rajurkar,et al.  Study of tribo-chemical lubricant film formation during application of nanolubricants in minimum quantity lubrication (MQL) grinding , 2012 .

[6]  Y. Xuan,et al.  Investigation on Convective Heat Transfer and Flow Features of Nanofluids , 2003 .

[7]  Ajay P. Malshe,et al.  Tribological study of nano lubricant integrated soybean oil for minimum quantity lubrication (MQL) grinding , 2010 .

[8]  W. Barthlott,et al.  Purity of the sacred lotus, or escape from contamination in biological surfaces , 1997, Planta.

[9]  W. Roetzel,et al.  TEMPERATURE DEPENDENCE OF THERMAL CONDUCTIVITY ENHANCEMENT FOR NANOFLUIDS , 2003 .

[10]  J. Nam,et al.  An experimental study on micro-grinding process with nanofluid minimum quantity lubrication (MQL) , 2012 .

[11]  John W. Sutherland,et al.  Dry Machining and Minimum Quantity Lubrication , 2004 .

[12]  Y. Liao,et al.  Effects of Cutting Fluid with Nano Particles on the Grinding of Titanium Alloys , 2010 .

[13]  Stephen Malkin,et al.  Grinding Technology: Theory and Applications of Machining with Abrasives , 1989 .

[14]  Zhixiong Zhou,et al.  The influence of spraying parameters on grinding performance for nanofluid minimum quantity lubrication , 2013 .

[15]  Albert J. Shih,et al.  Application of Nanofluids in Minimum Quantity Lubrication Grinding , 2008 .

[16]  N. R. Dhar,et al.  The influence of minimum quantity of lubrication (MQL) on cutting temperature, chip and dimensional accuracy in turning AISI-1040 steel , 2006 .

[17]  J. Eastman,et al.  Measuring Thermal Conductivity of Fluids Containing Oxide Nanoparticles , 1999 .

[18]  M. C. Shaw.  Principles of Abrasive Processing , 1996 .

[19]  Y. Z. Zhang,et al.  Studies on Mechanisms and Improvement of Workpiece Burn During Grinding of Titanium Alloys , 1990 .

[20]  J. A. Sánchez,et al.  Complementary tribometers for the analysis of contact phenomena in grinding , 2014 .

[21]  Liqiu Wang,et al.  Review of Heat Conduction in Nanofluids , 2011 .

[22]  J. Eastman,et al.  Enhanced thermal conductivity through the development of nanofluids , 1996 .

[23]  N. Fang,et al.  A comparative study of the cutting forces in high speed machining of Ti–6Al–4V and Inconel 718 with a round cutting edge tool , 2009 .

[24]  Jason Chuang,et al.  Experimental microchannel heat sink performance studies using nanofluids , 2007 .

[25]  M. Jackson,et al.  Abrasive Tools and Bonding Systems , 2011 .