Study on Load Bearing Characteristics of Novel Expandable Deepwater Drilling Conductor Based on Laboratory Experiment and Field Test

[1]  Tao Li,et al.  Self-Weight Penetration Characteristics of the Suction Foundation with Different Diameters in Sand , 2022, China Ocean engineering.

[2]  Liangbin Xu,et al.  Dynamic Bayesian networks based approach for risk analysis of subsea wellhead fatigue failure during service life , 2019, Reliab. Eng. Syst. Saf..

[3]  Zheng-li Liu,et al.  Study on Safety Control Technology of Surface Conductor Jetting Penetration in Ultra-Deep Water Soft Formation Drilling , 2019 .

[4]  Ti Dong,et al.  Load bearing characteristics study on novel deepwater composite drilling conductor by simulation and experimental methods , 2018, Journal of Petroleum Science and Engineering.

[5]  Xiaocong Yu,et al.  Field experimental investigation of bit stick-out for different soil strengths during deepwater conductor injection , 2018, Journal of Petroleum Science and Engineering.

[6]  Jin Yang,et al.  Research and development of compressible foam for pressure management in casing annulus of deepwater wells , 2018, Journal of Petroleum Science and Engineering.

[7]  Z. Guan,et al.  Risk Assessment Method of Subsea Wellhead Instability in Consideration of Uncertain Factors in Deepwater Drilling , 2018 .

[8]  J. Thibodeaux,et al.  The Operational Benefits of 30-in. Casing While Drilling CwD Conductor Installation , 2018 .

[9]  Stephen Butt,et al.  An innovative device to enhance conductor bearing capacity in deepwater drilling operations , 2018 .

[10]  Wei Meng,et al.  Method of predicting soil mechanical parameters in shallow formation while jetting process in deep-water drilling , 2017 .

[11]  Praisont Prasertamporn,et al.  Enhanced Deepwater Conductor Jetting Design for East Malaysia , 2016 .

[12]  S. Natarajan,et al.  Enhancement of Structural Conductor Design and Execution of Jetting Operations for Ultra-Deepwater Wells in Brunei , 2016 .

[13]  Bo Zhou,et al.  Model and experimental study on jetting flow rate for installing surface conductor in deep-water , 2016 .

[14]  Deli Gao,et al.  Finite element analysis of deepwater conductor bearing capacity to analyze the subsea wellhead stability with consideration of contact interface models between pile and soil , 2015 .

[15]  Bin Chen,et al.  Design of conductor soaking time in deepwater drilling , 2014 .

[16]  Hao Li,et al.  Numerical Simulation of Jet Excavation in Conductor Jetting Operations , 2014 .

[17]  Milton F Pereira,et al.  Deepwater Conductor Pre-Installation for First TLWP in Brazil , 2013 .

[18]  Bo Zhou,et al.  Bit stick-out calculation for the deepwater conductor jetting technique , 2013 .

[19]  Farrel Zwerneman,et al.  Insights into Using the 22nd Edition of API RP 2A Recommended Practice for Planning, Designing and Constructing Fixed Offshore Platforms - Working Stress Design , 2012 .

[20]  Thomas Jay Akers,et al.  Jetting of Structural Casing in Deepwater Environments: Job Design and Operational Practices , 2008 .

[21]  D. Griffin,et al.  Finite-Element Analysis , 1975 .

[22]  Teng Wang,et al.  Study on deepwater conductor jet excavation mechanism in cohesive soil , 2019, Applied Ocean Research.

[23]  B. Mackenzie,et al.  Conductor Jetting Experiences In Deepwater Offshore Ghana - An Investigation Into Geotechnical And Operational Influences On Success, And Establishment of Future Best Practice , 2012 .

[24]  Trond Eggen Sivertsen,et al.  New Well Foundation Concept, As Used at a Norwegian Sea Well , 2011 .

[25]  Jin Yang,et al.  Research of Conductor Setting Depth Using Jetting in the Surface of Deepwater , 2010 .

[26]  Su Yi,et al.  Mechanical stability analysis of subsea wellhead for deepwater drilling , 2008 .

[27]  Philippe Jeanjean,et al.  Innovative Design Method for Deepwater Surface Casings , 2002 .