Swirl flow tube reactor technology: An experimental and computational fluid dynamics study

A novel reactor technology for steam cracking reactors, called Swirl Flow Tube (SFT), has been evaluated experimentally and computationally. A comprehensive experimental dataset has been acquired on a newly built test set-up covering a wide range of Re numbers (30,000–120,000) and different swirl flow tube designs. The swirl flow tubes result in an increase of heat transfer by a factor of 1.2–1.5 compared to a straight tube. The increased heat transfer is accompanied by an increased pressure drop by a factor 1.4–2.2 compared to a straight tube depending on Reynolds number and geometry. A computational fluid dynamics model was adopted that is able to capture the main flow properties of the swirl flow tube and this model allows to attribute the increased heat transfer and pressure drop to a higher wall shear stress. The experimental and simulation results confirm the great potential for the application of the SFT technology in steam cracking furnaces because of the lower average wall temperatures and the resulting reduction of coke formation in the reactor coil.

[1]  M. Bajus,et al.  Coke formation during the pyrolysis of hydrocarbons in the presence of sulphur compounds , 1985 .

[2]  Charles J. Mueller,et al.  Recent progress in the development of diesel surrogate fuels , 2009 .

[3]  D. Kunzru,et al.  Sodium silicate as a coke inhibitor during naphtha pyrolysis , 1992 .

[4]  Harry M. Woerde,et al.  Mitigate coke formation , 2002 .

[5]  Tommy Detemmerman,et al.  Three Dimensional Coupled Simulation of Furnaces and Reactor Tubes for the Thermal Cracking of Hydrocarbons , 1998 .

[6]  Kevin Van Geem,et al.  Dimensional analysis for scaling up and down steam cracking coils , 2007 .

[7]  A. Najafi,et al.  An experimental study and CFD analysis towards heat transfer and fluid flow characteristics of decaying swirl pipe flow generated by axial vanes , 2010 .

[8]  Mohammad Hassan Saidi,et al.  Numerical analysis of turbulent swirling decay pipe flow , 2005 .

[9]  Paul Broutin,et al.  Anticoking Coatings for High Temperature Petrochemical Reactors , 1999 .

[10]  N. Chen.  An Explicit Equation for Friction Factor in Pipe , 1979 .

[11]  Martin Kumar Patel,et al.  Steam cracking and methane to olefins: Energy use, CO2 emissions and production costs , 2008 .

[12]  Long Liang,et al.  A dynamic adaptive chemistry scheme for reactive flow computations , 2009 .

[13]  Guy Marin,et al.  Kinetic Modeling of Coke Formation during Steam Cracking , 2002 .

[14]  D. J. Doorly,et al.  Mixing Through Stirring of Steady Flow in Small Amplitude Helical Tubes , 2009, Annals of Biomedical Engineering.

[15]  J. V. Albano,et al.  Application of extended surfaces in pyrolysis coils , 1988 .

[16]  Kevin Van Geem,et al.  Two Severity Indices for Scale-Up of Steam Cracking Coils , 2005 .

[17]  Martin Kumar Patel,et al.  Petrochemicals from oil, natural gas, coal and biomass: Production costs in 2030–2050 , 2009 .

[18]  H. Grabke,et al.  Mechanisms of simultaneous sulfidation and oxidation of FeCr and FeCrNi-alloys and of the failure of protective chromia scales , 1990 .

[19]  Don W. Green,et al.  Perry's Chemical Engineers' Handbook , 2007 .

[20]  C. M. Schillmoller,et al.  Use alloys to improve ethylene production : Petrochemical developments , 1996 .

[21]  N. Cheshire,et al.  Preliminary comparative study of small amplitude helical and conventional ePTFE arteriovenous shunts in pigs , 2005, Journal of The Royal Society Interface.

[22]  V. Gnielinski.  New equations for heat and mass transfer in turbulent pipe and channel flow , 1976 .

[23]  Georgios H. Vatistas,et al.  Reynolds Stress Model in the Prediction of Confined Turbulent Swirling Flows , 2006 .

[24]  R. R. Tacina,et al.  Numerical Study of Nonreacting Gas Turbine Combustor Swirl Flow Using Reynolds Stress Model , 2003 .

[25]  M. Wolfshtein.  The velocity and temperature distribution in one-dimensional flow with turbulence augmentation and pressure gradient , 1969 .

[26]  Guy Marin,et al.  Effect of radial temperature profiles on yields in steam cracking , 2004 .

[27]  Guy Marin,et al.  The Influence of Dimethyl Disulfide on Naphtha Steam Cracking , 2001 .

[28]  F. Qian,et al.  Comprehensive CFD simulation of product yields and coking rates for a Floor- and wall-fired naphtha cracking furnace , 2011 .

[29]  Kevin Van Geem,et al.  Influence of Silicon and Silicon/Sulfur-Containing Additives on Coke Formation during Steam Cracking of Hydrocarbons , 2008 .

[30]  Marianthi G. Ierapetritou,et al.  Integration of on‐the‐fly kinetic reduction with multidimensional CFD , 2009 .

[31]  J. Yoo,et al.  A numerical study on steady flow in helically sinuous vascular prostheses. , 2011, Medical engineering & physics.

[32]  Gilbert F. Froment,et al.  FIREBOX SIMULATION OF OLEFIN UNITS , 1989 .

[33]  J. J. De Saegher,et al.  Three Dimensional Simulation of High Severity Internally Finned Cracking Coils for Olefins Production , 1996 .

[34]  W. Green,et al.  An Exact-Steady-state Adaptive Chemistry method for combustion simulations: Combining the efficiency of reduced models and the accuracy of the full model , 2012 .