Study on burr occurrence and surface integrity during slot milling of multidirectional and plain woven CFRPs

[1]  K. Wegener,et al.  Influence of fibre orientation, tool geometry and process parameters on surface quality in milling of CFRP , 2017 .

[2]  Zhenyuan Jia,et al.  Effects of cutting edge radius and fiber cutting angle on the cutting-induced surface damage in machining of unidirectional CFRP composite laminates , 2017 .

[3]  Ming Chen,et al.  Occurrence and formation mechanism of surface cavity defects during orthogonal milling of CFRP laminates , 2017 .

[4]  Kai Guo,et al.  The effect of cutting temperature in milling of carbon fiber reinforced polymer composites , 2016 .

[5]  Oleg Tsoumarev,et al.  Prediction of surface roughness in slotting of CFRP , 2016 .

[6]  Oleg Tsoumarev,et al.  Effect of tool geometry on surface roughness in slotting of CFRP , 2016 .

[7]  N. Rajesh Mathivanan,et al.  An experimental investigation on the process parameters influencing machining forces during milling of carbon and glass fiber laminates , 2016 .

[8]  Jie Sun,et al.  Evaluation of cutting force and cutting temperature in milling carbon fiber-reinforced polymer composites , 2016 .

[9]  Konrad Wegener,et al.  Machining of carbon fiber reinforced plastics: Influence of tool geometry and fiber orientation on the machining forces , 2015 .

[10]  Wolfgang Hintze,et al.  Influence of weave structure on delamination when milling CFRP , 2015 .

[11]  Redouane Zitoune,et al.  Study of the surface defects and dust generated during trimming of CFRP: Influence of tool geometry, machining parameters and cutting speed range , 2014 .

[12]  Adem Çiçek,et al.  Prediction of Damage Factor in end Milling of Glass Fibre Reinforced Plastic Composites Using Artificial Neural Network , 2013, Applied Composite Materials.

[13]  Hossein Cheraghi,et al.  Machining Damage in Edge Trimming of CFRP , 2012 .

[14]  Yiğit Karpat,et al.  Mechanistic force modeling for milling of unidirectional carbon fiber reinforced polymer laminates , 2012 .

[15]  Wolfgang Hintze,et al.  Occurrence and propagation of delamination during the machining of carbon fibre reinforced plastics (CFRPs) – An experimental study , 2011 .

[16]  J. Paulo Davim,et al.  Damage and dimensional precision on milling carbon fiber-reinforced plastics using design experiments , 2005 .

[17]  Constantinos Soutis,et al.  Fibre reinforced composites in aircraft construction , 2005 .

[18]  J. Paulo Davim,et al.  A study on milling of glass fiber reinforced plastics manufactured by hand-lay up using statistical analysis (ANOVA) , 2004 .

[19]  Liangchi Zhang,et al.  An experimental investigation into the orthogonal cutting of unidirectional fibre reinforced plastics , 2003 .

[20]  Yan Jin,et al.  An energy based force prediction method for UD-CFRP orthogonal machining , 2017 .

[21]  Hao Li,et al.  Machinability analysis on helical milling of carbon fiber reinforced polymer , 2015 .

[22]  Byung-Joo Kim,et al.  Carbon Fibers and Their Composites , 2015 .

[23]  Amanda Jacob,et al.  Carbon fibre and cars – 2013 in review , 2014 .

[24]  Azwan Iskandar Azmi,et al.  Machinability study of glass fibre-reinforced polymer composites during end milling , 2013 .

[25]  Wolfgang Hintze,et al.  Modeling of Delamination During Milling of Unidirectional CFRP , 2013 .

[26]  Yiğit Karpat,et al.  Milling Force Modelling of Multidirectional Carbon Fiber Reinforced Polymer Laminates , 2012 .

[27]  Roberto Teti,et al.  Machining of Composite Materials , 2002 .