Thermal analysis of a solar parabolic trough receiver tube with porous insert optimized by coupling genetic algorithm and CFD

In this paper, the heat transfer enhancement in a solar parabolic trough receiver tube with porous insert and non-uniform heat flux condition was investigated. A new optimization method, which couples genetic algorithm (GA) and computational fluid dynamics (CFD) based on Socket communication, was proposed to optimize the configuration of porous insert. After the acquisition of the optimal porous inserts, some performance evaluation criterions such as synergy angle, entransy dissipation and exergy loss were introduced to discuss the heat transfer performance of the enhanced receiver tubes (ERTs) with optimal and referenced porous inserts. The results showed that, for a large range of properties of porous insert (including porosity and thermal conductivity) and Reynolds number, the heat-transfer performance of ERT with porous insert optimized by GA is always higher than that of the referenced ERTs. Better heat-transfer performance can further improve the solar-to-thermal energy conversion efficiency and mechanical property of the solar parabolic trough receiver. When some porous materials with high thermal conductivity are adopted, ERT can simultaneously obtain perfect thermal and thermo-hydraulic performance with using the same optimized porous insert, which cannot be achieved by using the referenced porous insert. In the view of those introduced evaluation criterions, using the optimized porous insert can obtain better synergy performance and lesser irreversibility of heat transfer than using the referenced porous insert. Entransy dissipation per unit energy transferred and exergy loss rate have equivalent effects on the evaluation of irreversibility of heat transfer process. These evaluation criterions can be used as optimization goals for enhancing the comprehensive performance of the solar parabolic trough receiver.

[1]  V. Gnielinski.  New equations for heat and mass transfer in the turbulent flow in pipes and channels , 1975 .

[2]  Ya-Ling He,et al.  Numerical optimization of catalyst configurations in a solar parabolic trough receiver–reactor with non-uniform heat flux , 2015 .

[3]  Ya-Ling He,et al.  Exergy analysis and optimization of charging–discharging processes of latent heat thermal energy storage system with three phase change materials , 2016 .

[4]  G. V. Satyanarayana,et al.  Numerical Study of Porous Finned Receiver for Solar Parabolic Trough Concentrator , 2008 .

[5]  Yangyang He,et al.  Numerical study of heat transfer enhancement by unilateral longitudinal vortex generators inside parabolic trough solar receivers , 2012 .

[6]  Xinhai Xu,et al.  Heat transfer fluids for concentrating solar power systems – A review , 2015 .

[7]  J. Muñoz,et al.  Analysis of internal helically finned tubes for parabolic trough design by CFD tools , 2011 .

[8]  Ming-Jia Li,et al.  Optimization of Porous Insert Configuration in a Central Receiver Tube for Heat Transfer Enhancement , 2015 .

[9]  Ming-Jia Li,et al.  Optimization of porous insert configurations for heat transfer enhancement in tubes based on genetic algorithm and CFD , 2015 .

[10]  M. Behnia,et al.  Modelling of Parabolic Trough Direct Steam Generation Solar Collectors , 1998, Renewable Energy.

[11]  Amin M. Elsafi.  Exergy and exergoeconomic analysis of sustainable direct steam generation solar power plants , 2015 .

[12]  G. Delussu,et al.  A qualitative thermo-fluid-dynamic analysis of a CO2 solar pipe receiver , 2012 .

[13]  Jian-Fei Zhang,et al.  A performance evaluation plot of enhanced heat transfer techniques oriented for energy-saving , 2009 .

[14]  Weiwei Yang,et al.  Simulation of the parabolic trough solar energy generation system with Organic Rankine Cycle , 2012 .

[15]  K. S. Reddy,et al.  Effect of porous disc receiver configurations on performance of solar parabolic trough concentrator , 2012 .

[16]  Aldo Steinfeld,et al.  An air-based corrugated cavity-receiver for solar parabolic trough concentrators , 2015 .

[17]  K. Ravi Kumar,et al.  Numerical Investigation of Energy-Efficient Receiver for Solar Parabolic Trough Concentrator , 2008 .

[18]  Yang Xu,et al.  Comparative and sensitive analysis for parabolic trough solar collectors with a detailed Monte Carlo ray-tracing optical model , 2014 .

[19]  J. Meyer,et al.  Heat transfer and thermodynamic performance of a parabolic trough receiver with centrally placed perforated plate inserts , 2014 .

[20]  D. Kearney,et al.  Test results: SEGS LS-2 solar collector , 1994 .

[21]  Ya-Ling He,et al.  Convective Heat Transfer Enhancement: Mechanisms, Techniques, and Performance Evaluation , 2014 .

[22]  S. C. Kaushik,et al.  State-of-the-art of solar thermal power plants—A review , 2013 .

[23]  Chao Xu,et al.  Parametric optimization of regenerative organic Rankine cycle (ORC) for low grade waste heat recovery using genetic algorithm , 2013 .

[24]  Ya-Ling He,et al.  Optimization for a Thermochemical Energy Storage-reactor based on Entransy Dissipation Minimization , 2015 .

[25]  Ali Akbar Ranjbar,et al.  Three-dimensional Numerical Analysis Of Heat Transfer Characteristics Of Solar Parabolic Collector With Two Segmental Rings , 2013 .

[26]  Ya-Ling He,et al.  A comprehensive model for optical and thermal characterization of a linear Fresnel solar reflector with a trapezoidal cavity receiver , 2016 .

[27]  Ya-Ling He,et al.  A MCRT and FVM coupled simulation method for energy conversion process in parabolic trough solar collector , 2011 .

[28]  Ya-Ling He,et al.  Numerical studies on the inherent interrelationship between field synergy principle and entransy dissipation extreme principle for enhancing convective heat transfer , 2014 .

[29]  Chang Xu,et al.  Numerical study of heat transfer enhancement in the receiver tube of direct steam generation with parabolic trough by inserting metal foams , 2013 .

[30]  Xungang Diao,et al.  A numerical study of parabolic trough receiver with nonuniform heat flux and helical screw-tape inserts , 2014 .

[31]  Ya-Ling He,et al.  An entransy dissipation-based optimization principle for solar power tower plants , 2014 .

[32]  W. Tao,et al.  The impact of concrete structure on the thermal performance of the dual-media thermocline thermal storage tank using concrete as the solid medium , 2014 .

[33]  Ya-Ling He,et al.  Analysis of thermal stress and fatigue fracture for the solar tower molten salt receiver , 2016 .

[34]  E. N. Sieder,et al.  Heat Transfer and Pressure Drop of Liquids in Tubes , 1936 .

[35]  K. R. Kumar,et al.  Thermal analysis of solar parabolic trough with porous disc receiver , 2009 .

[36]  Eckhard Lüpfert,et al.  Advances in Parabolic Trough Solar Power Technology , 2002 .

[37]  Ming-Jia Li,et al.  Thermal analysis of solar central receiver tube with porous inserts and non-uniform heat flux , 2017 .

[38]  Wei Liu,et al.  Enhancing heat transfer in the core flow by using porous medium insert in a tube , 2010 .

[39]  Ya-Ling He,et al.  A design method and numerical study for a new type parabolic trough solar collector with uniform solar flux distribution , 2014 .

[40]  Wei Zhang,et al.  Three-dimensional numerical study of heat transfer characteristics of plain plate fin-and-tube heat exchangers from view point of field synergy principle , 2005 .

[41]  Ya-Ling He,et al.  Numerical investigations on a pressurized volumetric receiver: Solar concentrating and collecting modelling , 2012 .