On the Use of Shear-Lag Methods for Analysis of Stress Transfer in Unidirectional Composites

Abstract The ‘shear-lag’ analysis method is frequently used for analysis of stress transfer between the fiber and the matrix in composites. The accuracy of shear-lag methods has not been critically assessed, in part because the assumptions have not been fully understood. This paper starts from the exact equations of elasticity for axisymmetric stress states in transversely isotropic materials and introduces the minimum assumptions required to derive the most commonly used shear-lag equations. These assumptions can now be checked to study the accuracy of shear-lag analysis on any problem. Some sample calculations were done for stress transfer from a matrix into a broken fiber. The shear-lag method did a reasonable job (within 20%) of predicting average axial stress in the fiber and total strain energy in the specimen provided the shear-lag parameter most commonly used in the literature is replaced by a new one derived from the approximate elasticity analysis. The shear-lag method does a much worse job of predicting shear stresses and energy release rates. Furthermore, the shear-lag method does not work for low fiber volume fractions.

[1]  J. Nairn,et al.  Stress transfer into a fragmented, anisotropic fiber through an imperfect interface , 1997 .

[2]  F. Leroy.  On analytical approaches to the three-dimensional stress state in a single fibre pull-out specimen , 1996 .

[3]  N. Wadsworth,et al.  Load transfer from broken fibres in composite materials , 1968 .

[4]  L. Penn,et al.  Improved analysis and experimental evaluation of the single filament pull-out test , 1992 .

[5]  R. Keunings,et al.  Modelling of critical fibre length and interfacial debonding in the fragmentation testing of polymer composites , 1992 .

[6]  P. Feillard,et al.  Theoretical aspects of the fragmentation test , 1994 .

[7]  M. Piggott,et al.  Debonding and friction at fibre-polymer interfaces. I: Criteria for failure and sliding , 1987 .

[8]  Jang-Kyo Kim,et al.  Interfacial debonding and fibre pull-out stresses , 1992 .

[9]  H. L. Cox.  The elasticity and strength of paper and other fibrous materials , 1952 .

[10]  C. Hsueh,et al.  Elastic load transfer from partially embedded axially loaded fibre to matrix , 1988 .

[11]  Y. Mai,et al.  Interfacial debonding and fibre pull-out stresses , 1994, Journal of Materials Science.

[12]  L. N. McCartney,et al.  New theoretical model of stress transfer between fibre and matrix in a uniaxially fibre-reinforced composite , 1989, Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences.

[13]  E. Reissner.  Analysis of shear lag in box beams by the principle of minimum potential energy , 1946 .

[14]  L. McCartney.  Stress transfer mechanics for multiple perfectly bonded concentric cylinder models of unidirectional composites. , 1993 .

[15]  L. McCartney.  Analytical Models of Stress Transfer in Unidirectional Composites and Cross-Ply Laminates, and Their Application to the Prediction of Matrix/Transverse Cracking , 1992 .

[16]  H. Wagner,et al.  Toughness of interfaces from initial fiber-matrix debonding in a single fiber composite fragmentation test , 1995 .

[17]  Zvi Hashin,et al.  Thermoelastic properties of fiber composites with imperfect interface , 1990 .

[18]  C. Galiotis,et al.  Interfacial Shear Stress Distribution in Model Composites Part 2: Fragmentation Studies on Carbon Fibre/Epoxy Systems , 1992 .

[19]  Analysis of the deformation of a symmetrically-loaded fiber embedded in a matrix material , 1991 .

[20]  John A. Nairn,et al.  A variational mechanics analysis of the stresses around breaks in embedded fibers , 1992 .

[21]  Chun-Hway Hsueh.  Modeling of elastic stress transfer in fiber-reinforced composites , 1995 .

[22]  J. Nairn,et al.  On the use of energy methods for interpretation of results of single-fiber fragmentation experiments , 1996 .

[23]  A. Nayfeh.  Thermomechanically induced interfacial stresses in fibrous composites , 1977 .

[24]  M S Troitsky,et al.  Stiffened plates: Bending, stability, and vibrations , 1976 .