A computationally efficient finite element model of wire and arc additive manufacture

Wire and arc additive manufacturing (WAAM) is an emerging technology which has the potential to significantly reduce material usage and manufacturing time through the production of near net-shape components with high deposition rates. One of the main problems of this process is the residual stresses and distortions of the deposited workpiece. To help understand and optimise the process, finite element (FE) models are commonly used; however, the conventional transient models are not efficient for simulating a large-scale WAAM process. In this paper, the stress evolution during the thermal cycles of the WAAM process was investigated with the help of a transient thermomechanical FE model. It was found that the peak temperatures experienced during the thermal cycles of the WAAM process determine the residual stress of that point. Based on this finding, an efficient “engineering” FE model was developed. Compared to the conventional transient thermomechanical approach, this model can save the computational time by 99 %. This new model produced distortion and residual stress predictions that were nearly identical to the original transient model and the experimental results.

[1]  Miguel Cervera,et al.  Finite element modeling of multi-pass welding and shaped metal deposition processes , 2010 .

[2]  Mark Whittaker,et al.  Shaped metal deposition of a nickel alloy for aero engine applications , 2008 .

[3]  Tso-Liang Teng,et al.  Effect of welding sequences on residual stresses , 2003 .

[4]  Wei Liang,et al.  Numerical simulation of welding distortion in large structures , 2007 .

[5]  Paul A. Colegrove,et al.  Welding process impact on residual stress and distortion , 2009 .

[6]  Philip J. Withers,et al.  Residual stress engineering in friction stir welds by roller tensioning , 2009 .

[7]  Yung C. Shin,et al.  Modeling of grain refinement in aluminum and copper subjected to cutting , 2011 .

[8]  Yashar Javadi,et al.  Influence of welding sequence on welding distortions in pipes , 2008 .

[9]  D. Deng,et al.  Prediction of welding distortion and residual stress in a thin plate butt-welded joint , 2008 .

[10]  Lu Zhang,et al.  Investigation of Lagrangian and Eulerian finite element methods for modeling the laser forming process , 2004 .

[11]  J. D. Spencer,et al.  Rapid prototyping of metal parts by three-dimensional welding , 1998 .

[12]  P. Michaleris,et al.  Prediction of welding distortion , 1997 .

[13]  M. Peel,et al.  Distortion control in welding by mechanical tensioning , 2007 .

[14]  P. Colegrove,et al.  Rolling to control residual stress and distortion in friction stir welds , 2010 .

[15]  Mohammad Pervez Mughal,et al.  The mechanical effects of deposition patterns in welding-based layered manufacturing , 2007 .

[16]  F. W. Brust,et al.  8 – Mitigating welding residual stress and distortion , 2005 .

[17]  Sehyung Park,et al.  3D welding and milling: part II—optimization of the 3D welding process using an experimental design approach , 2005 .

[18]  M. Koçak,et al.  Residual stress in friction stir-welded Al sheets , 2004 .

[19]  Zhili Feng.  Processes and mechanisms of welding residual stress and distortion , 2005 .

[20]  Pierluigi Mollicone,et al.  Computational methods and experimental validation of welding distortion models , 2007 .

[21]  F. Prinz,et al.  Thermal stresses and deposition patterns in layered manufacturing , 2001 .

[22]  J. Goldak,et al.  A new finite element model for welding heat sources , 1984 .

[23]  P. Michaleris,et al.  Evaluation of 2D, 3D and applied plastic strain methods for predicting buckling welding distortion and residual stress , 2006 .

[24]  Tom Gray,et al.  Computational prediction of out-of-plane welding distortion and experimental investigation , 2005 .

[25]  B. Baufeld,et al.  Additive manufacturing of Ti–6Al–4V components by shaped metal deposition: Microstructure and mechanical properties , 2010 .

[26]  S. C. Park,et al.  Weldin g Distortion of a Thin-Plate Panel Structure , 1999 .

[27]  John Goldak,et al.  Simulation on the thermal cycle of a welding process by space–time convection–diffusion finite element analysis , 2009 .

[28]  Paul A. Colegrove,et al.  Thermo-mechanical analysis of Wire and Arc Additive Layer Manufacturing process on large multi-layer parts , 2011 .