Fabrication of optically smooth, through-wafer silicon molds for PDMS total internal reflection-based devices

This paper presents a systematic approach to fabricate optically smooth, through-wafer silicon (Si) molds for polymer optical devices, in particular poly(dimethylsiloxane) (PDMS) total internal reflection (TIR)-based devices. First, the Si molds were fabricated by an optimized, through-wafer deep reactive ion etching (DRIE) process to achieve small roughness. To further reduce the roughness, the Si molds were then oxidized and etched in BHF for three times to achieve surface roughness average (Ra) and root mean square (RMS) roughness below 25 nm while peak-to-valley (P–V) roughness is below 150 nm. We monitored the surface roughness and morphology of the sidewalls of Si mold through three cycles of oxidation and BHF etching using field emission scanning electron microscopy (FESEM) and atomic force microscopy (AFM). We found that further oxidation and BHF etching might not have much effect in further reducing the roughness while the device feature definitions might be compromised. Finally, the PDMS TIR-based devices replicated from the Si molds were evaluated by means of FESEM, AFM and by imaging of the fluorescent evanescent spots.

[1]  Ranganathan Nagarajan,et al.  Development of dual-etch via tapering process for through-silicon interconnection , 2007 .

[2]  Gottlieb S. Oehrlein,et al.  Study of sidewall passivation and microscopic silicon roughness phenomena in chlorine‐based reactive ion etching of silicon trenches , 1990 .

[3]  D. Nilsson,et al.  Fabrication of silicon molds for polymer optics , 2003 .

[4]  G. J. Davies,et al.  Sidewall roughness characterization and comparison between silicon and SU-8 microcomponents , 2007 .

[5]  Reza Abdolvand,et al.  An advanced reactive ion etching process for very high aspect-ratio sub-micron wide trenches in silicon , 2008 .

[6]  M. Schmidt,et al.  Characterization of a Time Multiplexed Inductively Coupled Plasma Etcher , 1999 .

[7]  K. Richter,et al.  Deep plasma silicon etch for microfluidic applications , 1999 .

[8]  W. Pike,et al.  Analysis of sidewall quality in through-wafer deep reactive-ion etching , 2004 .

[9]  J. Miao,et al.  Mechanical and microstructural characterization of high aspect ratio through-wafer electroplated copper interconnects , 2007 .

[10]  Xin Zhang,et al.  A six-wafer combustion system for a silicon micro gas turbine engine , 2000, Journal of Microelectromechanical Systems.

[11]  Susumu Sugiyama,et al.  Versatile microfluidic total internal reflection (TIR)-based devices: application to microbeads velocity measurement and single molecule detection with upright and inverted microscope. , 2009, Lab on a chip.

[12]  S. Sugiyama,et al.  A dual-color Total Internal Reflection (TIR)-based chip for simultaneous detection of two fluorophores , 2008, Italian National Conference on Sensors.

[13]  Stefan Sinzinger,et al.  Microoptics: SINZINGER:MICROOPTICS 2ED O-BK , 2005 .

[14]  Aaron J. Knobloch,et al.  Micro, Internal-Combustion Engine Fabrication With 900 µm Deep Features Via DRIE , 2003 .

[15]  K. R. Williams,et al.  Novel interconnection technologies for integrated microfluidic systems , 1998 .

[16]  S. Sugiyama,et al.  A Monolithic Dual-Color Total-Internal-Reflection-Based Chip for Highly Sensitive and High-Resolution Dual-Fluorescence Imaging , 2009, Journal of Microelectromechanical Systems.

[17]  J. Fluitman,et al.  A survey on the reactive ion etching of silicon in microtechnology , 1996 .

[18]  Jyrki Kiihamäki,et al.  Etching through silicon wafer in inductively coupled plasma , 2000 .

[19]  S. Sugiyama,et al.  Design, simulation and fabrication of a total internal reflection (TIR)-based chip for highly sensitive fluorescent imaging , 2007 .

[20]  S. Beeby,et al.  Performance improvement of a vibration-powered electromagnetic generator by reduced silicon surface roughness , 2008 .

[21]  Martin A. Schmidt,et al.  Inertial sensor technology using DRIE and wafer bonding with connecting capability , 1999 .

[22]  J. M. Noworolski,et al.  Silicon fusion bonding and deep reactive ion etching: a new technology for microstructures , 1996 .

[23]  Sami Franssila,et al.  Mask material effects in cryogenic deep reactive ion etching , 2007 .

[24]  K. Saraswat,et al.  Two-dimensional thermal oxidation of silicon—I. Experiments , 1987, IEEE Transactions on Electron Devices.

[25]  Mark S. Sherwin,et al.  Two-dimensional terahertz photonic crystals fabricated by deep reactive ion etching in Si , 2003 .

[26]  S. Bhansali,et al.  Fabrication of vertical mirrors using plasma etch and KOH:IPA polishing , 2007 .

[27]  M. Gretillat,et al.  Vertical mirrors fabricated by deep reactive ion etching for fiber-optic switching applications , 1997 .