Investigation on the Potential of High Efficiency for Internal Combustion Engines

The current brake thermal efficiency of advanced internal combustion engines is limited to 50%, and how to further improve the efficiency is a challenge. In this study, a theoretical investigation on engine thermal efficiency was carried out using one-dimension simulations based on the first law of thermodynamics. The energy balance was evaluated by varying parameters such as compression ratio (CR); heat transfer coefficient; intake charge properties; and combustion phasing etc.—their influences on the efficiency limits were demonstrated. Results show that for a given heat transfer coefficient, an optimal CR exists to obtain the peak efficiency. The optimal CR decreases with the increase of heat transfer coefficient, and high CR with a low heat-transfer coefficient can achieve a significantly high efficiency. A higher density and specific heat ratio of intake charge, as well as a shorter combustion duration with a proper CA50 (crank angle at 50% of total heat release), can increase efficiency significantly. Methanol shows an excellent ability in decreasing the peak in-cylinder temperature; and the peak indicated efficiency is relatively higher than other tested fuels. The displacement has few effects on the indicated efficiency, while it shows a strong effect on the energy distribution between heat transfer and exhaust energy. All these strategies with high CR result in high in-cylinder pressure and temperature; which means a breakthrough of material is needed in the future.

[1]  Hao Wang,et al.  Performance analysis and parametric optimum criteria of a quantum Otto heat engine with heat transfer effects , 2009 .

[2]  Alberto Boretti,et al.  Energy Recovery in Passenger Cars , 2012 .

[3]  A. Sanjid,et al.  Energy balance of internal combustion engines using alternative fuels , 2013 .

[4]  Leonidas Ntziachristos,et al.  What is the Real-World CO2 Reduction Benefit of the 95 g/km Passenger Car Average Emission Target to be Reached by 2020? , 2012 .

[5]  K. Hoag,et al.  An appraisal of advanced engine concepts using second law analysis techniques , 1984 .

[6]  Adnan Parlak,et al.  The effect of thermal barrier coating on a turbo-charged Diesel engine performance and exergy potential of the exhaust gas , 2005 .

[7]  Adnan Parlak,et al.  The effect of heat transfer on performance of the Diesel cycle and exergy of the exhaust gas stream in a LHR Diesel engine at the optimum injection timing , 2005 .

[8]  Peter Eilts,et al.  Investigation of Extreme Mean Effective and Maximum Cylinder Pressures in a Passenger Car Diesel Engine , 2013 .

[9]  Mazhar Hussain,et al.  Combustion, Performance, and Emission Evaluation of a Diesel Engine with Biodiesel Like Fuel Blends Derived From a Mixture of Pakistani Waste Canola and Waste Transformer Oils , 2017 .

[10]  Kwee-Yan Teh,et al.  Thermodynamic requirements for maximum internal combustion engine cycle efficiency. Part 2: Work extraction and reactant preparation strategies , 2008 .

[11]  Dimitrios C. Rakopoulos,et al.  Theoretical Study of the Effects of Spark Timing on the Performance and Emissions of a Light-Duty Spark Ignited Engine Running under Either Gasoline or Ethanol or Butanol Fuel Operating Modes , 2017 .

[12]  Kwee-Yan Teh,et al.  Thermodynamic requirements for maximum internal combustion engine cycle efficiency. Part 1: Optimal combustion strategy , 2008 .

[13]  Imdat Taymaz,et al.  An experimental study of energy balance in low heat rejection diesel engine , 2006 .

[14]  Hua Zhao,et al.  Effects of Oxygen Content of Fuels on Combustion and Emissions of Diesel Engines , 2016 .

[15]  Dimitrios Karonis,et al.  Alternative Diesel from Waste Plastics , 2017 .

[16]  Bin Tang,et al.  Combustion Performance and Emission Characteristics of a Diesel Engine Using a Water-Emulsified Heavy Fuel Oil and Light Diesel Blend , 2015 .

[17]  Mark Savill,et al.  Pulse Detonation Assessment for Alternative Fuels , 2017 .

[18]  Zhen Huang,et al.  Experimental study of the two-stage injection process of fatty acid esters on a common rail injection system , 2016 .

[19]  Murray H. Edson.  The Influence of Compression Ratio and Dissociation on Ideal Otto Cycle Engine Thermal Efficiency , 1962 .

[20]  Christopher F. Edwards,et al.  DIESEL SPRAY BEHAVIOR AT COMPRESSION RATIOS UP TO 100:1 , 2010 .

[21]  I. Taymaz,et al.  Experimental investigation of heat losses in a ceramic coated diesel engine , 2003 .

[22]  Jane Hupe,et al.  Energy End-Use: Transport , 2012 .

[23]  J. Kossmann,et al.  Identification of an Arabidopsis inorganic pyrophosphatase capable of being imported into chloroplasts , 2004, FEBS letters.

[24]  Pablo Olmeda,et al.  Experimental analysis of the global energy balance in a DI diesel engine , 2015 .

[25]  Zhen Huang,et al.  Macroscopic and microscopic spray characteristics of fatty acid esters on a common rail injection system , 2017 .

[26]  John B. Heywood,et al.  Internal combustion engine fundamentals , 1988 .

[27]  Zhen Huang,et al.  Numerical study on fuel physical effects on the split injection processes on a common rail injection system , 2017 .