Integrated Product and Process Design for a Flapping Wing Drive Mechanism

Successful realization of a flapping wing micro-air vehicle (MAV) requires development of a light weight drive mechanism that can convert the continuous rotary motion of the motor into oscillatory flapping motion of the wings. The drive mechanism should have low weight to maximize the payload and battery capacity. It should also have high power transmission efficiency to maximize the operational range and to minimize weight of the motor. In order to make flapping wing MAVs attractive in search, rescue, and recovery efforts, they should be disposable from the cost point of view. Injection molded compliant drive mechanisms are an attractive design option because of manufacturing scalability and reduction in the number of parts. However, realizing compliant drive mechanism using injection molding requires use of multipiece multigate molds. Molding process constraints need to be considered during the design stage to successfully realize the drive mechanism. This paper describes an approach for determining the drive mechanism shape and size that meets both the design and molding requirements. The novel aspects of this work include (1) minimizing the number of mold pieces and (2) the use of sacrificial shape elements to reduce the impact of the weld-lines on the structural performance. The design generated by the approach described in this paper was utilized to realize an operational flapping wing MAV.

[1]  M. Goldfarb,et al.  The Development of Elastodynamic Components for Piezoelectrically Actuated Flapping Micro-Air Vehicles , 2002 .

[2]  G. K. Ananthasuresh,et al.  A Novel Compliant Mechanism for Converting Reciprocating Translation Into Enclosing Curved Paths , 2004 .

[3]  Rafał Żbikowski,et al.  Materials challenges in the design of an insect-like flapping wing mechanism based on a four-bar linkage , 2007 .

[4]  Jay Shoemaker,et al.  Moldflow Design Guide: A Resource for Plastics Engineers , 2006 .

[5]  Dale R. Shires,et al.  A hybrid global–local approach for optimization of injection gate locations in liquid composite molding process simulations , 2007 .

[6]  Tanakorn Tantanawat,et al.  Design of Compliant Mechanisms for Minimizing Input Power in Dynamic Applications , 2007 .

[7]  Sunil K. Agrawal,et al.  Design and Optimization of a Mechanism for Out-of-Plane Insect Winglike Motion With Twist , 2005 .

[8]  S C Burgess,et al.  Design of a parallel crank-rocker flapping mechanism for insect-inspired micro air vehicles , 2007 .

[9]  Suresh G. Advani,et al.  Use of genetic algorithms to optimize gate and vent locations for the resin transfer molding process , 1999 .

[10]  Robert A. Malloy,et al.  Plastic Part Design for Injection Molding: An Introduction , 1994 .

[11]  John P. Beaumont,et al.  Successful Injection Molding: Process, Design, and Simulation , 2002 .

[12]  Andrew Y. C. Nee,et al.  Computer-Aided Injection Mold Design and Manufacture , 2004 .

[13]  Satyandra K. Gupta,et al.  Geometric algorithms for automated design of multi-piece permanent molds , 2004, Comput. Aided Des..

[14]  S.K. Agrawal,et al.  Energetics-based design of small flapping-wing micro air vehicles , 2006, IEEE/ASME Transactions on Mechatronics.

[15]  Sunil K. Agrawal,et al.  Biologically Inspired Design Of Small Flapping Wing Air Vehicles Using Four-Bar Mechanisms And Quasi-steady Aerodynamics , 2005 .

[16]  Prosenjit Gupta,et al.  Computing a flattest, undercut-free parting line for a convex polyhedron, with application to mold design , 1996, Comput. Geom..

[17]  D. Kazmer.  Injection Mold Design Engineering , 2007 .

[18]  Hong Zhou,et al.  Shape and Size Synthesis of Compliant Mechanisms Using Wide Curve Theory , 2006 .

[19]  G. Menges,et al.  How to make injection molds , 1987 .

[20]  M. Madou.  Fundamentals of microfabrication , 1997 .

[21]  John P. Beaumont,et al.  Runner and Gating Design Handbook: Tools for Successful Injection Molding , 2004 .

[22]  Patrick Zdunich,et al.  Development and Testing of the Mentor Flapping-wing Micro Air Vehicle , 2007 .