Comprehensive analytical model for locally contacted rear surface passivated solar cells

For optimum performance of solar cells featuring a locally contacted rear surface, the metallization fraction as well as the size and distribution of the local contacts are crucial, since Ohmic and recombination losses have to be balanced. In this work we present a set of equations which enable to calculate this trade off without the need of numerical simulations. Our model combines established analytical and empirical equations to predict the energy conversion efficiency of a locally contacted device. For experimental verification, we fabricate devices from float zone silicon wafers of different resistivity using the laser fired contact technology for forming the local rear contacts. The detailed characterization of test structures enables the determination of important physical parameters, such as the surface recombination velocity at the contacted area and the spreading resistance of the contacts. Our analytical model reproduces the experimental results very well and correctly predicts the optimum cont...

[1]  K. Bothe,et al.  Structure and transformation of the metastable boron- and oxygen-related defect center in crystalline silicon , 2004 .

[2]  Wilhelm Warta,et al.  Minority carrier lifetime degradation in boron-doped Czochralski silicon , 2001 .

[3]  A. W. Stephens,et al.  High‐eficiency silicon solar cells: Si/SiO2, interface parameters and their impact on device performance , 1994 .

[4]  Stefan W. Glunz,et al.  Theory and experiments on the back side reflectance of silicon wafer solar cells , 2008 .

[5]  K. Catchpole,et al.  Modelling the PERC structure for industrial quality silicon , 2002 .

[6]  Stefan W. Glunz,et al.  Investigation of laser‐fired rear‐side recombination properties using an analytical model , 2006 .

[7]  Karsten Bothe,et al.  Fundamental boron–oxygen‐related carrier lifetime limit in mono‐ and multicrystalline silicon , 2005 .

[8]  A. Cuevas,et al.  Electronic properties of light-induced recombination centers in boron-doped Czochralski silicon , 1999 .

[9]  M. Green,et al.  Intrinsic carrier concentration and minority‐carrier mobility of silicon from 77 to 300 K , 1993 .

[10]  Andreas Schenk,et al.  Finite-temperature full random-phase approximation model of band gap narrowing for silicon device simulation , 1998 .

[11]  R. H. Cox,et al.  Ohmic contacts for GaAs devices , 1967 .

[12]  M. Shur,et al.  Disk and stripe capacitances , 1995 .

[13]  W. Warta,et al.  Injection‐level‐dependent recombination velocities at the Si‐SiO2 interface for various dopant concentrations , 1994 .

[14]  M. Green,et al.  Two‐dimensional numerical optimization study of the rear contact geometry of high‐efficiency silicon solar cells , 1994 .

[15]  Alistair B. Sproul,et al.  Dimensionless solution of the equation describing the effect of surface recombination on carrier decay in semiconductors , 1994 .

[16]  Richard H. Bube,et al.  Fundamentals of solar cells , 1983 .

[17]  Andreas Wolf,et al.  Advanced analytical model for the effective recombination velocity of locally contacted surfaces , 2010 .

[18]  P. Altermatt,et al.  Reassessment of the intrinsic carrier density in crystalline silicon in view of band-gap narrowing , 2003 .

[19]  A. Mette,et al.  Thermal oxidation for crystalline silicon solar cells exceeding 19% efficiency applying industrially feasible process technology , 2008 .

[20]  D.B.M. Klaassen,et al.  A unified mobility model for device simulation—II. Temperature dependence of carrier mobility and lifetime , 1992 .

[21]  M. Shur,et al.  Spreading resistance of a round ohmic contact , 1993 .

[22]  M. Green,et al.  22.8% efficient silicon solar cell , 1989 .

[23]  M. Green,et al.  Spatially resolved analysis and minimization of resistive losses in high-efficiency Si solar cells , 1996 .

[24]  A. Cuevas,et al.  General parameterization of Auger recombination in crystalline silicon , 2002 .

[25]  M. Green.  Intrinsic concentration, effective densities of states, and effective mass in silicon , 1990 .

[26]  D. Biro,et al.  Optimizing annealing steps for crystalline silicon solar cells with screen printed front side metallization and an oxide‐passivated rear surface with local contacts , 2009 .

[27]  Stefan W. Glunz,et al.  Enhanced lateral current transport via the front N+ diffused layer of n‐type high‐efficiency back‐junction back‐contact silicon solar cells , 2009 .

[28]  Siegfried Selberherr,et al.  Simulation of Semiconductor Devices and Processes , 1994, Springer Vienna.

[29]  M. Green,et al.  High‐efficiency silicon solar cells: Full factor limitations and non‐ideal diode behaviour due to voltage‐dependent rear surface recombination velocity , 1993 .

[30]  Daniel Kray,et al.  Analysis of ultrathin high‐efficiency silicon solar cells , 2009, Renewable Energy.

[31]  Marc Rüdiger,et al.  Modeling and optimization study of industrial n-type high-efficiency back-contact back-junction silicon solar cells , 2010 .

[32]  S. Karmalkar,et al.  Compact Models of Spreading Resistances for Electrical/Thermal Design of Devices and ICs , 2007, IEEE Transactions on Electron Devices.

[33]  R. Brendel,et al.  Injection and Collection Diffusion Lengths of Polycrystalline Thin-Film Solar Cells , 1999 .

[34]  R. Brendel,et al.  Analytical model for the diode saturation current of point‐contacted solar cells , 2006 .

[35]  D.B.M. Klaassen,et al.  A unified mobility model for device simulation—I. Model equations and concentration dependence , 1992 .

[36]  R. D. Brooks,et al.  Spreading resistance between constant potential surfaces , 1971 .