An alternative method to record rising temperatures during dental implant site preparation: a preliminary study using bovine bone.

Overheating is constantly mentioned as a risk factor for bone necrosis that could compromise the dental implant primary stability. Uncontrolled thermal injury can result in a fibrous tissue, interpositioned at the implant-bone interface, compromising the long-term prognosis. The methods used to record temperature rise include either direct recording by thermocouple instruments or indirect estimating by infrared thermography. This preliminary study was carried out using bovine bone and a different method of temperatures rising estimation is presented. Two different types of drills were tested using fluoroptic thermometer and the effectiveness of this alternative temperature recording method was evaluated.

[1]  Tomas Albrektsson,et al.  Thermal injury to bone , 1982 .

[2]  Edwin A McGlumphy,et al.  Heat production by 3 implant drill systems after repeated drilling and sterilization. , 2006, Journal of oral and maxillofacial surgery : official journal of the American Association of Oral and Maxillofacial Surgeons.

[3]  T. Albrektsson,et al.  Thermally induced bone necrosis in rabbits: relation to implant failure in humans. , 1985, Clinical orthopaedics and related research.

[4]  C. Lavelle,et al.  Effect of internal irrigation on frictional heat generated from bone drilling. , 1980, Journal of oral surgery.

[5]  Carl E Misch,et al.  Heat generation during implant drilling: the significance of motor speed. , 2002, Journal of oral and maxillofacial surgery : official journal of the American Association of Oral and Maxillofacial Surgeons.

[6]  L. S. Matthews,et al.  Temperatures measured in human cortical bone when drilling. , 1972, The Journal of bone and joint surgery. American volume.

[7]  G. Krekeler,et al.  Atraumatic surgical technique and implant bed preparation. , 1992, Quintessence international.

[8]  R M Jochum,et al.  Influence of multiple use of Timedur-titanium cannon drills: thermal response and scanning electron microscopic findings. , 2000, Clinical oral implants research.

[9]  S. Szmukler‐Moncler,et al.  Influence of different parameters on bone heating and drilling time in implantology. , 1997, Clinical oral implants research.

[10]  F Watanabe,et al.  Heat distribution in bone during preparation of implant sites: heat analysis by real-time thermography. , 1992, The International journal of oral & maxillofacial implants.

[11]  D L Hussey,et al.  Temperature changes in bovine mandibular bone during implant site preparation: an assessment using infra-red thermography. , 1996, Journal of dentistry.

[12]  T Albrektsson,et al.  Heat caused by drilling cortical bone. Temperature measured in vivo in patients and animals. , 1984, Acta orthopaedica Scandinavica.

[13]  E. Keleşoğlu,et al.  Effects of irrigation temperature on heat control in vitro at different drilling depths. , 2009, Clinical oral implants research.

[14]  S. Iyer,et al.  Effects of drill speed on heat production and the rate and quality of bone formation in dental implant osteotomies. Part I: Relationship between drill speed and heat production. , 1997, The International journal of prosthodontics.

[15]  S. Iyer,et al.  Effects of drill speed on heat production and the rate and quality of bone formation in dental implant osteotomies. Part II: Relationship between drill speed and healing. , 1997, The International journal of prosthodontics.

[16]  J A Hobkirk,et al.  Investigation of variable factors in drilling bone. , 1977, Journal of oral surgery.

[17]  T Albrektsson,et al.  Temperature threshold levels for heat-induced bone tissue injury: a vital-microscopic study in the rabbit. , 1983, The Journal of prosthetic dentistry.

[18]  Han-Joo Lee,et al.  The influence of drill wear on cutting efficiency and heat production during osteotomy preparation for dental implants: a study of drill durability. , 2004, The International journal of oral & maxillofacial implants.

[19]  Tomas Albrektsson,et al.  Measurements of shaft speed while drilling through bone , 1995 .

[20]  Abouzgia Mb,et al.  Temperature rise during drilling through bone. , 1997 .

[21]  R. Adell,et al.  Temperatures during drilling for the placement of implants using the osseointegration technique. , 1986, Journal of oral and maxillofacial surgery : official journal of the American Association of Oral and Maxillofacial Surgeons.

[22]  U. Brägger,et al.  Heat generated during preparation of titanium implants of the ITI Dental Implant System: an in vitro study. , 1995, Clinical Oral Implants Research.

[23]  T Albrektsson,et al.  The effect of heat on bone regeneration: an experimental study in the rabbit using the bone growth chamber. , 1984, Journal of oral and maxillofacial surgery : official journal of the American Association of Oral and Maxillofacial Surgeons.

[24]  D. F. James,et al.  Temperature rise during drilling through bone. , 1997, The International journal of oral & maxillofacial implants.

[25]  M. Klein,et al.  The effect of irrigation on osteotomy depth and bur diameter. , 1996, The International journal of oral & maxillofacial implants.

[26]  T Albrektsson,et al.  Thermal injury to bone. A vital-microscopic description of heat effects. , 1982, International journal of oral surgery.

[27]  Z Majzoub,et al.  Heat generation during implant site preparation: an in vitro study. , 1997, The International journal of oral & maxillofacial implants.

[28]  P. Lamey,et al.  Thermal changes observed at implant sites during internal and external irrigation. , 2002, Clinical oral implants research.

[29]  W R Krause,et al.  Temperature elevations in orthopaedic cutting operations. , 1982, Journal of biomechanics.

[30]  C. Hirsch,et al.  Factors affecting the determination of the physical properties of femoral cortical bone. , 1966, Acta orthopaedica Scandinavica.

[31]  S H Tehemar,et al.  Factors affecting heat generation during implant site preparation: a review of biologic observations and future considerations. , 1999, The International journal of oral & maxillofacial implants.

[32]  Brisman Dl,et al.  The effect of speed, pressure, and time on bone temperature during the drilling of implant sites. , 1996 .

[33]  Radford C. Tanzer,et al.  Temperature measured in human cortical bone when drilling , 1972 .

[34]  T. Albrektsson,et al.  Microcirculation in grafted bone. A chamber technique for vital microscopy of rabbit bone transplants. , 1978, Acta orthopaedica Scandinavica.

[35]  Toma Udiljak,et al.  Determination of spatial distribution of increase in bone temperature during drilling by infrared thermography: preliminary report , 2008, Archives of Orthopaedic and Trauma Surgery.

[36]  K. Takakura,et al.  Thermological study of drilling bone tissue with a high-speed drill. , 2000, Neurosurgery.

[37]  Shu Chien,et al.  Heat shock‐induced necrosis and apoptosis in osteoblasts , 1999, Journal of orthopaedic research : official publication of the Orthopaedic Research Society.

[38]  Rafel Ss.  Temperature changes during high-speed drilling on bone. , 1962 .