Numerical and model validation of uncovered nanofluid sheet and tube type photovoltaic thermal solar system

Abstract In this paper, an experimental and numerical study is performed to evaluate the performance of a photovoltaic thermal (PV/T) nanofluid based collector. A two-dimensional numerical model is established to study the effects of using nanofluids as working fluid in PV/T collector. The model is validated experimentally by comparing the simulations with the experimental results. The influence of concentration (0.1, 0.2 and 0.4 wt.%), types of nanoparticles (Al2O3 and Cu) and different base fluids (pure water and ethylene glycol) on the electrical and thermal performance of the collector is investigated. Also, the model is applied to predict the annual electrical and thermal output of the PV/T for three different cities: Lyon (France), Mashhad (Iran) and Monastir (Tunisia). The results indicated that using pure water as a base fluid provides a higher performance in comparison with ethylene glycol. Using Cu/water gives the best thermal and electrical efficiency in comparison to Cu/ethylene glycol, Al2O3/water and Al2O3/ethylene glycol. It is also found that the thermal and electrical energy output for Monastir (Tunisia) climate condition is higher than that of Mashhad (Iran) and Lyon (France).

[1]  C. Ménézo,et al.  Study of the thermal and electrical performances of PVT solar hot water system , 2014 .

[2]  Dae Hyun Kim,et al.  Simulation and model validation of sheet and tube type photovoltaic thermal solar system and conventional solar collecting system in transient states , 2012 .

[3]  Y. Xuan,et al.  Investigation on Convective Heat Transfer and Flow Features of Nanofluids , 2003 .

[4]  Hicham Zerradi,et al.  New Nusselt number correlations to predict the thermal conductivity of nanofluids , 2014 .

[5]  Tin-Tai Chow,et al.  Hybrid photovoltaic and thermal solar-collector designed for natural circulation of water , 2006 .

[6]  Christophe Menezo,et al.  Efficient single glazed flat plate photovoltaic–thermal hybrid collector for domestic hot water system , 2011 .

[7]  D. L. Evans,et al.  Simplified method for predicting photovoltaic array output , 1980 .

[8]  Gilles Notton,et al.  Thermal behavior of a copolymer PV/Th solar system in low flow rate conditions , 2009 .

[9]  Clement Kleinstreuer,et al.  Concentration photovoltaic–thermal energy co-generation system using nanofluids for cooling and heating , 2014 .

[10]  Saeed Zeinali Heris,et al.  Experimental investigation of the effects of silica/water nanofluid on PV/T (photovoltaic thermal units) , 2014 .

[11]  A. Mojtabi,et al.  Numerical Simulation of Cooling a Solar Cell by Forced Convection in the Presence of a Nanofluid , 2012 .

[12]  Oussama Rejeb,et al.  Parameters effect analysis of a photovoltaic thermal collector: Case study for climatic conditions of Monastir, Tunisia , 2015 .

[13]  Masoud Rahimi,et al.  Heat transfer enhancement in a PV cell using Boehmite nanofluid , 2014 .

[14]  O. Pourmehran,et al.  Statistical optimization of microchannel heat sink (MCHS) geometry cooled by different nanofluids using RSM analysis , 2015 .

[15]  Oussama Rejeb,et al.  A numerical investigation of a photovoltaic thermal (PV/T) collector , 2015 .

[16]  W. Swinbank.  Long‐wave radiation from clear skies , 1963 .

[17]  W. Sark,et al.  Annual performance enhancement of building integrated photovoltaic modules by applying phase change materials , 2013 .

[18]  A. Akisawa,et al.  The performance of PV‐t systems for residential application in Bangkok , 2013 .

[19]  J. Maxwell.  A Treatise on Electricity and Magnetism , 1873, Nature.

[20]  S. Iniyan,et al.  Performance analysis of a copper sheet laminated photovoltaic thermal collector using copper oxide – water nanofluid , 2015 .

[21]  Ha Herbert Zondag,et al.  The yield of different combined PV-thermal collector designs , 2003 .

[22]  B. Sandnes,et al.  A photovoltaic/thermal (PV/T) collector with a polymer absorber plate. Experimental study and analytical model , 2002 .