Computational fluid dynamics modeling of polymer electrolyte membrane fuel cells

A detailed steady-state isothermal two-dimensional model of a proton exchange membrane fuel cell has been developed. A finite element method was used to solve this multi-component transport model coupled with flow in porous medium, charge balance, electrochemical kinetics, and a rigorous water balance in the membrane. The model-predicted fuel cell performance curves are compared with published experimental results and a good agreement was found. The complex water balance in the membrane was investigated and the operating conditions where the membrane becomes dehydrated were identified. The effects of channel width and bipolar plate shoulder dimensions, porosity, and the relative humidity of the inlet streams on the fuel cell performance are evaluated. It was found that smaller width channels and bipolar plate shoulders were required for high current density operations. As the electrode area under the bipolar plate shoulder increases, the fuel cell benefits more from higher porosity electrodes. The anode gas stream's relative humidity was found to be more critical for fuel cell performance than the cathode gas relative humidity.

[1]  Sadik Kakac,et al.  Two‐dimensional model for proton exchange membrane fuel cells , 1998 .

[2]  Chaoyang Wang,et al.  Three-dimensional analysis of transport and electrochemical reactions in polymer electrolyte fuel cells , 2004 .

[3]  Mark W. Verbrugge,et al.  A Mathematical Model of the Solid‐Polymer‐Electrolyte Fuel Cell , 1992 .

[4]  Xianguo Li,et al.  Carbon monoxide poisoning of proton exchange membrane fuel cells , 2001 .

[5]  Chao-Yang Wang,et al.  In situ water distribution measurements in a polymer electrolyte fuel cell , 2003 .

[6]  Chao-Yang Wang,et al.  Two-phase transport and the role of micro-porous layer in polymer electrolyte fuel cells , 2004 .

[7]  Ralph E. White,et al.  A water and heat management model for proton-exchange-membrane fuel cells , 1993 .

[8]  Shimshon Gottesfeld,et al.  Characterization of polymer electrolytes for fuel cell applications , 1993 .

[9]  Chao-Yang Wang,et al.  Large-scale simulation of polymer electrolyte fuel cells by parallel computing , 2004 .

[10]  Edson A. Ticianelli,et al.  Localization of platinum in low catalyst loading electrodes to to attain high power densities in SPE fuel cells , 1988 .

[11]  J. Weidner,et al.  Diffusion of water in Nafion 115 membranes , 2000 .

[12]  A. Parthasarathy,et al.  Temperature Dependence of the Electrode Kinetics of Oxygen Reduction at the Platinum/Nafion® Interface—A Microelectrode Investigation , 1992 .

[13]  T. Springer,et al.  Polymer Electrolyte Fuel Cell Model , 1991 .

[14]  Ned Djilali,et al.  A 3D, Multiphase, Multicomponent Model of the Cathode and Anode of a PEM Fuel Cell , 2003 .

[15]  R. Reid,et al.  The Properties of Gases and Liquids , 1977 .

[16]  Viral S. Mehta,et al.  Review and analysis of PEM fuel cell design and manufacturing , 2003 .

[17]  Don W. Green,et al.  Perry's Chemical Engineers' Handbook , 2007 .

[18]  Xianguo Li,et al.  Modelling of polymer electrolyte membrane fuel cells with variable degrees of water flooding , 2000 .

[19]  T. Fuller,et al.  Water and Thermal Management in Solid‐Polymer‐Electrolyte Fuel Cells , 1993 .

[20]  Ned Djilali,et al.  Three-dimensional computational analysis of transport phenomena in a PEM fuel cell—a parametric study , 2003 .

[21]  Chao-Yang Wang,et al.  Computational Fluid Dynamics Modeling of Proton Exchange Membrane Fuel Cells , 2000 .

[22]  Ned Djilali,et al.  THREE-DIMENSIONAL COMPUTATIONAL ANALYSIS OF TRANSPORT PHENOMENA IN A PEM FUEL CELL , 2002 .

[23]  Shimshon Gottesfeld,et al.  The Water Content Dependence of Electro-Osmotic Drag in Proton-Conducting Polymer Electrolytes , 1995 .

[24]  K. M. Chittajallu,et al.  Design and optimization of polymer electrolyte membrane (PEM) fuel cells , 2004 .

[25]  Ned Djilali,et al.  Computational model of a PEM fuel cell with serpentine gas flow channels , 2004 .