Effect of in-process active cooling on forming quality and efficiency of tandem GMAW–based additive manufacturing

Wire arc additive manufacturing (WAAM), utilizing welding arc to melt metal wire into shaped parts, has become a promising manufacturing technology recently. Tandem GMAW–based WAAM (TG-WAAM), in which two wires are fed into the molten pool simultaneously, has the potential to double the efficiency of traditional WAAM. However, the high wire-feed speed is accompanied with high heat input that is likely to cause molten pool overflowing, especially at upper layers because of decreased heat dissipation and increased heat accumulation. An in-process active cooling technology based on thermoelectric cooling is introduced into TG-WAAM in this research. Its effect on forming quality and efficiency of TG-WAAM is investigated experimentally. The results show that the additional cooling well compensates for the excessive heat input into the molten pool, which enables not only increased maximum wire-feed speed (9–15%) but also reduced inter-layer dwell time (42–54%), while maintaining the desired forming quality. The overall efficiency is improved by more than 0.97 times in the case study. This research provides a feasible scheme to solve the conflict between forming quality and efficiency during WAAM.

[1]  Yun Zhao,et al.  In-process control of distortion in wire and arc additive manufacturing based on a flexible multi-point support fixture , 2018, Science and Technology of Welding and Joining.

[2]  Chenglei Diao,et al.  Oxide accumulation effects on wire + arc layer-by-layer additive manufacture process , 2018 .

[3]  G. Tan,et al.  A review of thermoelectric cooling: Materials, modeling and applications , 2014 .

[4]  Guangjun Zhang,et al.  Forming appearance analysis in multi-layer single-pass GMAW-based additive manufacturing , 2015 .

[5]  Hui Chen,et al.  Fabrication of inclined thin-walled parts in multi-layer single-pass GMAW-based additive manufacturing with flat position deposition , 2017 .

[6]  P. Forêt,et al.  The Influence of Gas Cooling in Context of Wire Arc Additive Manufacturing—A Novel Strategy of Affecting Grain Structure and Size , 2017 .

[7]  Fang Li,et al.  Adaptive process control of wire and arc additive manufacturing for fabricating complex-shaped components , 2018 .

[8]  Jing-Hui Meng,et al.  Transient modeling and dynamic characteristics of thermoelectric cooler , 2013 .

[9]  Xin Lin,et al.  Optimisation of interpass temperature and heat input for wire and arc additive manufacturing 5A06 aluminium alloy , 2017 .

[10]  Lin Wu,et al.  Bead geometry prediction for robotic GMAW-based rapid manufacturing through a neural network and a second-order regression analysis , 2012, Journal of Intelligent Manufacturing.

[11]  F. Martina.  Investigation of methods to manipulate geometry, microstructure and mechanical properties in titanium large scale Wire+Arc Additive Manufacturing , 2014 .

[12]  Jun Xiong,et al.  Closed-loop control of variable layer width for thin-walled parts in wire and arc additive manufacturing , 2016 .

[13]  J. Ding,et al.  Thermo-mechanical analysis of wire and arc additive manufacturing process , 2012 .

[14]  Huijun Li,et al.  A practical path planning methodology for wire and arc additive manufacturing of thin-walled structures , 2015 .

[15]  Fang Li,et al.  Thermoelectric Cooling-Aided Bead Geometry Regulation in Wire and Arc-Based Additive Manufacturing of Thin-Walled Structures , 2018 .

[16]  Zengxi Pan,et al.  Wire-feed additive manufacturing of metal components: technologies, developments and future interests , 2015 .

[17]  F. Martina,et al.  Design for Additive Manufacturing , 2019 .

[18]  David W. Rosen,et al.  Design for Additive Manufacturing , 2015, Additive Manufacturing Technologies.

[19]  Matthias Finkbeiner,et al.  Environmental energy efficiency of single wire and tandem gas metal arc welding , 2017, Welding in the World.

[20]  Andrey Koptyug,et al.  Additive manufacturing of ITER first wall panel parts by two approaches: Selective laser melting and electron beam melting , 2017 .

[21]  Jian Han,et al.  Effects of heat accumulation on the arc characteristics and metal transfer behavior in Wire Arc Additive Manufacturing of Ti6Al4V , 2017 .

[22]  Qiang Zhan,et al.  A wire deflection detection method based on image processing in wire + arc additive manufacturing , 2017 .

[23]  B. Baufeld,et al.  Additive manufacturing of Ti–6Al–4V components by shaped metal deposition: Microstructure and mechanical properties , 2010 .

[24]  Fang Li,et al.  Evaluation and Optimization of a Hybrid Manufacturing Process Combining Wire Arc Additive Manufacturing with Milling for the Fabrication of Stiffened Panels , 2017 .

[25]  Gang Zhao,et al.  A comparative study of additively manufactured thin wall and block structure with Al-6.3% Cu alloy using cold metal transfer process , 2017 .

[26]  Xueming Hua,et al.  Arc Interference Behavior during Twin Wire Gas Metal Arc Welding Process , 2013 .