A Novel Approach for Development and Evaluation of LiDAR Navigated Electronic Maize Seeding System Using Check Row Quality Index

Crop geometry plays a vital role in ensuring proper plant growth and yield. Check row planting allows adequate space for weeding in both direction and allowing sunlight down to the bottom of the crop. Therefore, a light detection and ranging (LiDAR) navigated electronic seed metering system for check row planting of maize seeds was developed. The system is comprised of a LiDAR-based distance measurement unit, electronic seed metering mechanism and a wireless communication system. The electronic seed metering mechanism was evaluated in the laboratory for five different cell sizes (8.80, 9.73, 10.82, 11.90 and 12.83 mm) and linear cell speed (89.15, 99.46, 111.44, 123.41 and 133.72 mm·s−1). The research shows the optimised values for the cell size and linear speed of cell were found to be 11.90 mm and 99.46 mm·s−1 respectively. A light dependent resistor (LDR) and light emitting diode (LED)-based seed flow sensing system was developed to measure the lag time of seed flow from seed metering box to bottom of seed tube. The average lag time of seed fall was observed as 251.2 ± 5.39 ms at an optimised linear speed of cell of 99.46 mm·s−1 and forward speed of 2 km·h−1. This lag time was minimized by advancing the seed drop on the basis of forward speed of tractor, lag time and targeted position. A check row quality index (ICRQ) was developed to evaluate check row planter. While evaluating the developed system at different forward speeds (i.e., 2, 3 and 5 km·h−1), higher standard deviation (14.14%) of check row quality index was observed at forward speed of 5 km·h−1.

[1]  Dilip Kumar,et al.  DESIGN AND DEVELOPMENT OF CALIBRATION UNIT FOR PRECISION PLANTER , 2013 .

[2]  Y. C. Bhatt,et al.  Development of Electronic Metering Mechanism for Precision Planting of Seeds , 2017 .

[3]  N. Raghuwanshi,et al.  Identification of Suitable Hydrological Models for Streamflow Assessment in the Kangsabati River Basin, India, by Using Different Model Selection Scores , 2021, Natural Resources Research.

[4]  S. D. Kachman,et al.  Alternative measures of accuracy in plant spacing for planters using single seed metering , 1995 .

[5]  Zhang Shun,et al.  Design and experimental study of the control system for precision seed-metering device. , 2014 .

[6]  N. Kumari,et al.  Hydrological Response to Agricultural Land Use Heterogeneity Using Variable Infiltration Capacity Model , 2020, Water Resources Management.

[7]  J. Baerdemaeker,et al.  Evaluation of Seed Distribution Uniformity of a Multi-flight Auger as a Grain Drill Metering Device , 2006 .

[8]  Hossein Navid,et al.  A practical approach to comparative design of non-contact sensing techniques for seed flow rate detection , 2017, Comput. Electron. Agric..

[9]  Md. Enamul Haque,et al.  Conservation agriculture for small holder rainfed farming: Opportunities and constraints of new mechanized seeding systems , 2012 .

[10]  Octavian Popescu,et al.  A New Concept for Seed Precision Planting , 2015 .

[11]  N. Kumari,et al.  An Approach for Estimation of Evapotranspiration by Standardizing Parsimonious Method , 2019, Agricultural Research.

[12]  Takashi Kataoka,et al.  Estimation of mass flow of seeds using fibre sensor and multiple linear regression modelling , 2013 .

[13]  A. F. Kheiralla,et al.  Development of an Opto-Electronic Monitoring System for Crop Planter Seed Metering Unit , 2011 .

[14]  A. A. Al-Mallahi,et al.  Application of fibre sensor in grain drill to estimate seed flow under field operational conditions , 2016, Comput. Electron. Agric..

[15]  B. B. Gaikwad,et al.  Design of a low-cost pneumatic seeder for nursery plug trays , 2008 .

[16]  N. Raghuwanshi,et al.  Evaluation of Variable-Infiltration Capacity Model and MODIS-Terra Satellite-Derived Grid-Scale Evapotranspiration Estimates in a River Basin with Tropical Monsoon-Type Climatology , 2017 .

[17]  H. S. Sidhu,et al.  Development and evaluation of the Turbo Happy Seeder for sowing wheat into heavy rice residues in NW India , 2015 .

[18]  Li Yang,et al.  Design and test of fault monitoring system for corn precision planter , 2015 .

[19]  Joachim Müller,et al.  Laboratory measurement of seed drill seed spacing and velocity of fall of seeds using high-speed camera system , 2006 .

[20]  A. Özmerzi,et al.  Mathematical Modelling of Vacuum Pressure on a Precision Seeder , 2004 .

[21]  M. S. Patwardhan,et al.  Development and functional test of electronic metering mechanism for bullock drawn Jyoti Multicrop planter. , 2009 .

[22]  Rajeev Kumar,et al.  Detection of flow of seeds in the seed delivery tube and choking of boot of a seed drill , 2018, Comput. Electron. Agric..

[23]  Andrew Guzzomi,et al.  Precision metering of Santalum spicatum (Australian Sandalwood) seeds , 2013 .

[24]  Jianping Hu,et al.  Development and Experimental Analysis of a Seeding Quantity Sensor for the Precision Seeding of Small Seeds , 2019, Sensors.

[25]  Ashutosh Kumar Singh,et al.  Development and evaluation of electronically controlled precision seed-metering device for direct-seeded paddy planter , 2016 .

[26]  Zhang Dongxing,et al.  Development of mechatronic driving system for seed meters equipped on conventional precision corn planter , 2015 .