Theoretical and experimental study on laser surface hardening by repetitive laser pulses

Abstract An analytical solution for the temperature variation in a semi-infinite workpiece heated by repetitive laser pulses has been derived and the effects of various process parameters, viz. laser power, beam diameter, scan speed, pulse duration, repetition frequency and duty cycle on the surface transformation hardening have been investigated. The study shows that the soaking time of the top surface layer at a temperature above the phase transformation temperature, on which the homogeneity of microstructure and the depth of hardening depend, can be increased by repetitive laser pulse heating in comparison to continuous wave laser heating. The depth of hardness increases with the number of incident laser pulses at low frequencies in the range of Hz. This has been demonstrated by comparing the surface hardness characteristics of AISI 1055 steel specimens resulted by the continuous wave and repetitive laser pulse hardening processes.

[1]  Juan Pou,et al.  Theoretical and experimental analysis of high power diode laser (HPDL) hardening of AISI 1045 steel , 2007 .

[2]  W. Steen,et al.  Heat hardening of metal surfaces with a scanning laser beam , 1986 .

[3]  R. Komanduri,et al.  Thermal analysis of laser surface transformation hardening—optimization of process parameters , 2004 .

[4]  B. Yilbas,et al.  Repetitive laser pulse heating analysis: Pulse parameter variation effects on closed form solution , 2006 .

[5]  Michael F. Ashby,et al.  The transformation hardening of steel surfaces by laser beams—I. Hypo-eutectoid steels , 1984 .

[6]  J. W. Hill,et al.  Surface treatments by laser , 1974 .

[7]  Giovanni Tani,et al.  An efficient model for laser surface hardening of hypo-eutectoid steels , 2010 .

[8]  A. Fortunato,et al.  Laser surface hardening of martensitic stainless steel hollow parts , 2010 .

[9]  V. Schulze,et al.  Prediction of phase transformations during laser surface hardening of AISI 4140 including the effects of inhomogeneous austenite formation , 2006 .

[10]  Michael K.H. Leung,et al.  Theoretical and experimental studies on laser transformation hardening of steel by customized beam , 2007 .

[11]  Lijue Xue,et al.  Discrete laser spot transformation hardening of AISI O1 tool steel using pulsed Nd:YAG laser , 2011 .

[12]  Ho-Jun Shin,et al.  Laser surface hardening of S45C medium carbon steel using ND:YAG laser with a continuous wave , 2007 .

[13]  J. Meijer,et al.  Optimization of Laser Beam Transformation Hardening by One Single Parameter , 1991 .

[14]  D. M. Roessler,et al.  LASER PROCESSING OF MATERIALS FOR AUTOMOTIVE APPLICATIONS , 1989 .

[15]  W. Wu,et al.  Numerical investigation on laser transformation hardening with different temporal pulse shapes , 2006 .

[16]  J. M. Amado,et al.  Laser transformation hardening of a tool steel: Simulation-based parameter optimization and experimental results , 2006 .

[17]  A. Fortunato,et al.  Prediction of hypo eutectoid steel softening due to tempering phenomena in laser surface hardening , 2008 .

[18]  Shrikant V. Joshi,et al.  Laser surface hardening of austempered (bainitic) ball bearing steel , 2007 .

[19]  M. J. Torkamany,et al.  Laser surface hardening of AISI 420 stainless steel treated by pulsed Nd:YAG laser , 2010 .

[20]  Carlos Soriano,et al.  Effect of laser surface hardening on the microstructure, hardness and residual stresses of austempered ductile iron grades , 2011 .

[21]  Frank Vollertsen,et al.  Endurance limit of pulsed laser hardened component-like specimens—Experiment and simulation , 2008 .

[22]  I. R. Pashby,et al.  Surface hardening of steel using a high power diode laser , 2003 .

[23]  A. Nath,et al.  Effect of laser surface hardening on En18 (AISI 5135) steel , 1999 .

[24]  B. Yilbas,et al.  Laser consecutive pulse heating and phase change: Influence of spatial distribution of laser pulse intensity on melting , 2009 .

[25]  W. M. Steen,et al.  Surface heat treatment of EnS steel using a 2kW continuous-wave CO2 laser , 1979 .

[26]  Yung C. Shin,et al.  Predictive modeling of multi-track laser hardening of AISI 4140 steel , 2008 .

[27]  Lin Li,et al.  An analysis of the effect of laser beam geometry on laser transformation hardening , 2006 .

[28]  Lin Li.  The advances and characteristics of high-power diode laser materials processing , 2000 .

[29]  M. Rappaz,et al.  A combined model for the description of austenitization, homogenization and grain growth in hypoeutectoid Fe–C steels during heating , 1999 .

[30]  Yung C. Shin,et al.  Predictive modeling and experimental results for laser hardening of AISI 1536 steel with complex geometric features by a high power diode laser , 2006 .

[31]  Yung C. Shin,et al.  Predictive modeling and experimental results for residual stresses in laser hardening of AISI 4140 steel by a high power diode laser , 2009 .

[32]  S. Na,et al.  Influence of heating rate on the laser surface hardening of a medium carbon steel , 1988 .

[33]  V. Schulze,et al.  Influence of cyclic temperature changes on the microstructure of AISI 4140 after laser surface hardening , 2007 .

[34]  Henrikki Pantsar,et al.  Relationship between processing parameters, alloy atom diffusion distance and surface hardness in laser hardening of tool steel , 2007 .

[35]  J. C. Jaeger,et al.  Conduction of Heat in Solids , 1952 .

[36]  Friedrich G. Bachmann,et al.  Industrial applications of high power diode lasers in materials processing , 2003 .

[37]  Sooho Kim,et al.  Laser transformation hardening of iron-carbon and iron- carbon- chromium steels , 1988 .

[38]  Kazutaka Fujita,et al.  JSME Int. J. , 1994 .

[39]  M. Rappaz,et al.  A two-dimensional diffusion model for the prediction of phase transformations: Application to austenitization and homogenization of hypoeutectoid Fe-C steels , 1997 .

[40]  V. Tagliaferri,et al.  Modelling of pulse-periodic energy flow action on metallic materials , 1991 .