Rapid prototyping and testing of 3d micro rockets using mechanical micro machining

The trend of miniaturization has been applied to the research of rockets to develop prototypes of micro rockets. In this paper, the development of a web-integrated prototyping system for three-dimensional micro rockets, and the results of combustion tests are discussed. The body of rocket was made of 6061 aluminum cylinder by lathe process. The three-dimensional micro nozzles were fabricated on the same aluminum by using micro endmills with φ100μm~φ500 μm diameter. Two types of micro nozzle were fabricated and compared for performance. The total mass of the rockets was 7.32 g and that of propellant (gun powder) was 0.65 g. The thrust-to-weight ratio was between 1.58 and 1.74, and the flight test with 45 degree launch angle from the ground resulted in 46 m~53 m of horizontal flight distance. In addition, ABS housing for the micro machined rocket was fabricated using Fused Deposition Modeling (FDM). A web-based design, fabrication, and test system for micro nozzles was proposed to integrate the distributed hardware resources. Test data was sent to the designer via the same web server for the faster feedback to the rocket designer.

[1]  J. Anderson,et al.  Modern Compressible Flow: With Historical Perspective , 1982 .

[2]  S. Spearing,et al.  Microfabrication of a high pressure bipropellant rocket engine , 2001 .

[3]  Scott D. Collins,et al.  Vaporizing liquid microthruster , 2000 .

[4]  Walter Hesse,et al.  Jet propulsion for aerospace applications , 1964 .

[5]  Zhao Jian Yang,et al.  Bearing load distribution studies in a multi bearing rotor system and a remote computing method based on the internet , 2004 .

[6]  R. B. Cohen,et al.  Digital MicroPropulsion , 1999, Technical Digest. IEEE International MEMS 99 Conference. Twelfth IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.99CH36291).

[7]  Fritz B. Prinz,et al.  RP of Si3N4 burner arrays via assembly mould SDM , 2004 .

[8]  Carole Rossi,et al.  Design, fabrication and modelling of MEMS-based microthrusters for space application , 2001 .

[9]  Dong-Soo Kim,et al.  MIMS: Web-based micro machining service , 2005, Int. J. Comput. Integr. Manuf..

[10]  Carole Rossi,et al.  Compact model based on a lumped parameter approach for the prediction of solid propellant micro-rocket performance , 2002 .

[11]  Young-Eui Shin,et al.  The Influences of Residual Stress on the Frequency of Ultrasonic Transducers with Composite Membrane Structure , 2006 .

[12]  Paul K. Wright,et al.  Web-based design and manufacturing systems for automobile components: Architectures and usability studies , 2002, Int. J. Comput. Integr. Manuf..

[13]  J. Anderson.  Modern compressible flow, with historical perspective - 2nd Edition , 1990 .

[14]  Soohyun Kim,et al.  Mobility Improvement of an Internet-based Robot System Using the Position Prediction Simulator , 2005 .

[15]  Won Jee Chung,et al.  Thermal model of high-speed spindle units , 2003 .

[16]  Carole Rossi,et al.  Prediction of the performance of a Si-micromachined microthruster by computing the subsonic gas flow inside the thruster , 2000 .

[17]  Henggao Ding,et al.  Study of a vaporizing water micro-thruster , 2001 .

[18]  Hong Hee Yoo,et al.  Modal Analysis of Rotating Beam Structures Having Complex Configurations Employing Multi-Reference Frames , 2006 .