Direct 3D visualization of the phase-separated morphology in chlorinated polyethylene/nylon terpolyamide based thermoplastic elastomers.

Blends of chlorinated polyethylene and nylon-6/-6,6/-12 terpolyamide were prepared. The ratio of the two components was systematically varied within the blends. The mechanical behavior of the samples was analyzed with tensile tests and dynamical mechanical analysis showing that, for several ratios, materials with improved mechanical properties typical of thermoplastic elastomers were obtained. In such a mechanical regime, a co-continuous phase-separated morphology was clearly evidenced at the microscopic scale by 3D laser scanning confocal fluorescent microscopy (LSCFM). At blend compositions where plastic tensile behavior is observed, LSCFM reveals dispersed spheres of one component in the other.

[1]  C. Macosko,et al.  Measurement of geometrical parameters in cocontinuous polymer blends: 3D versus 2D image analysis , 2011, Journal of microscopy.

[2]  C. McNeill,et al.  Simultaneous Surface and Bulk Imaging of Polymer Blends with X-ray Spectromicroscopy. , 2010, Macromolecular rapid communications.

[3]  C. Macosko,et al.  Direct measurement of interface anisotropy of bicontinuous structures via 3D image analysis. , 2010, Langmuir : the ACS journal of surfaces and colloids.

[4]  R. J. Gaymans,et al.  Elastic properties of thermoplastic elastomers based on poly(tetramethylene oxide) and monodisperse amide segments , 2010, Journal of Materials Science.

[5]  N. Felorzabihi,et al.  Investigation of morphology and miscibility of isotactic polypropylene, ethylene‐butene copolymer and chlorinated polyolefin blends via LSCFM, SEM, WAXD, and DMA , 2009 .

[6]  Shenglan Zhang,et al.  Preparation and characterization of biodegradable thermoplastic Elastomers (PLCA/PLGA blends) , 2009 .

[7]  T. Hashimoto,et al.  Sponge-like Heterogeneous Gels: Hierarchical Structures in Poly(N-isopropylacrylamide) Chemical Gels As Observed by Combined Scattering and Confocal Microscopy Method , 2008 .

[8]  K. Matyjaszewski,et al.  PBA-PMMA 3-arm star block copolymer thermoplastic elastomers , 2008 .

[9]  S. Kiatkamjornwong,et al.  Thermoplastic elastomer based on high-density polyethylene/natural rubber blends: rheological, thermal, and morphological properties , 2008 .

[10]  E. G. Bajsić,et al.  Blends of thermoplastic polyurethane and polypropylene. I. Mechanical and phase behavior , 2007 .

[11]  M. Gonçalves,et al.  Structure and Morphology of Poly(ε-caprolactone)/Chlorinated Polyethylene (PCL/PECl) Blends Investigated by DSC, Simultaneous SAXS/WAXD, and Elemental Mapping by ESI-TEM , 2007 .

[12]  K. Müllen,et al.  Synthesis and Self-Organization of Core-Extended Perylene Tetracarboxdiimides with Branched Alkyl Substituents , 2006 .

[13]  A. Karim,et al.  Characterization of elastomeric blends by atomic force microscopy , 2006 .

[14]  Sabu Thomas,et al.  Micro- and Nanostructured Multiphase Polymer Blend Systems : Phase Morphology and Interfaces , 2005 .

[15]  G. McKinley,et al.  Miscibility and viscoelastic properties of acrylic polyhedral oligomeric silsesquioxane–poly(methyl methacrylate) blends , 2005 .

[16]  T. K. Chaki,et al.  Polyamide-6,6/in situ silica hybrid nanocomposites by sol–gel technique: synthesis, characterization and properties , 2005 .

[17]  J. Noordermeer,et al.  Three‐Dimensional Structure of Olefinic Thermoplastic Elastomer Blends Using Electron Tomography , 2005 .

[18]  J. Mewis,et al.  Phase morphology and stability of co-continuous (PPE/PS)/PA6 and PS/PA6 blends: effect of rheology and reactive compatibilization , 2004 .

[19]  Hiroshi Jinnai,et al.  Emerging Technologies for the 3D Analysis of Polymer Structures , 2004 .

[20]  H. Janik,et al.  Multiphase‐Separated Polyurethanes Studied by Micro‐Raman Spectroscopy , 2003 .

[21]  L. Leibler,et al.  Design and properties of co-continuous nanostructured polymers by reactive blending , 2002, Nature materials.

[22]  M. Winnik,et al.  Novel Morphology Evolution in Thick Films of a Polymer Blend , 2002 .

[23]  U. Ishiaku,et al.  Characterisation of PVC/NBR and PVC/ENR50 binary blends and PVC/ENR50/NBR ternary blends by DMA and solid state NMR , 2001 .

[24]  E. Martuscelli,et al.  Review Properties of blends and composites based on poly(3-hydroxy)butyrate (PHB) and poly(3-hydroxybutyrate-hydroxyvalerate) (PHBV) copolymers , 2000 .

[25]  S. Stoeva,et al.  Thermal analysis study on the degradation of the solid-state chlorinated poly(ethylene) , 2000 .

[26]  R. Jerome,et al.  Synthesis and Characterization of Poly(methyl methacrylate)-block-poly(n-butyl acrylate)-block-poly(methyl methacrylate) Copolymers by Two-Step Controlled Radical Polymerization (ATRP) Catalyzed by NiBr2(PPh3)2, 1† , 1999 .

[27]  R. Willemse,et al.  Tensile moduli of co-continuous polymer blends , 1999 .

[28]  A. Draaijer,et al.  Confocal laser scanning microscopy : a new method for determination of the morphology of polymer blends , 1993 .

[29]  A. Coran,et al.  Rubber-Thermoplastic Compositions. Part VII. Chlorinated Polyethylene Rubber-Nylon Compositions , 1983 .