Dropwise cooling: Experimental tests by infrared thermography and numerical simulations

Abstract In this paper, infrared thermography is used to measure the transient contact temperature between impinging droplets and hot solid surfaces. Droplets are released onto the heated solid surface of a barium fluoride (BaF2) disk, which has a high transmittance (about 90%) in the 8–12 μm range (typical of longwave infrared cameras). The interface temperature is measured from below, through the solid material, by infrared thermography. Since the solid is IR-transparent, a black coating layer is used to allow radiative heating of the surface and provide a method to measure the liquid–solid interface temperature. A numerical code is then presented, which simulates the evaporation of water droplets on hot solid surfaces. At the present stage of development, single-phase evaporation is addressed. The three-dimensional energy diffusion equation, discretized using the finite volume method, is employed to model the transient within both the droplets and the solid substrate. The numerical results are validated by comparison with the experimental data.

[1]  Dropwise evaporative cooling , 1991 .

[2]  Paolo Tartarini,et al.  Effect of liquid-solid contact angle on droplet evaporation , 1996 .

[3]  L. Wachters,et al.  The heat transfer from a hot horizontal plate to sessile water drops in the spherodial state , 1966 .

[4]  L. Bolle,et al.  SPRAY COOLING OF HOT SURFACES , 1982 .

[5]  J. Rizza.  A Numerical Solution to Dropwise Evaporation , 1981 .

[6]  C. Avedisian,et al.  On the collision of a droplet with a solid surface , 1991, Proceedings of the Royal Society of London. Series A: Mathematical and Physical Sciences.

[7]  D. D. Evans,et al.  Evaporative cooling due to a gently deposited droplet , 1993 .

[8]  I. Mudawar,et al.  Film boiling heat transfer of droplet streams and sprays , 1997 .

[9]  R. Good,et al.  A Thermodynamic Derivation of Wenzel's Modification of Young's Equation for Contact Angles; Together with a Theory of Hysteresis1 , 1952 .

[10]  M. Marengo,et al.  Secondary atomisation produced by single drop vertical impacts onto heated surfaces , 2005 .

[11]  Alberto Muscio,et al.  Experimental tests of dropwise cooling on infrared-transparent media , 2007 .

[12]  W. J. Herzberg,et al.  Relationship between contact angle and drop size , 1970 .

[13]  N. K. Adam,et al.  CCL.—Angles of contact and polarity of solid surfaces , 1925 .

[14]  Marco Marengo,et al.  Analysis of impact of droplets on horizontal surfaces , 2002 .

[15]  D. D. Evans,et al.  Evaporation of a Water Droplet Deposited on a Hot High Thermal Conductivity Surface , 1986 .

[16]  Hiroshi Kawamura,et al.  Transient Temperature Profile of a Hot Wall Due to an Impinging Liquid Droplet , 1978 .

[17]  J. C. Jaeger,et al.  Conduction of Heat in Solids , 1952 .

[18]  Carlos Alberto Brebbia,et al.  Advanced Computational Methods in Heat Transfer III , 1994 .

[19]  T. Vermeulen,et al.  The receding contact angle , 1970 .

[20]  L. Wachters,et al.  The heat transfer from a hot wall to impinging water drops in the spheroidal state , 1966 .

[21]  Carlos Alberto Brebbia,et al.  A formulation of the boundary element method for axisymmetric transient heat conduction , 1981 .

[22]  John D. Bernardin,et al.  Mapping of impact and heat transfer regimes of water drops impinging on a polished surface , 1997 .