Dispenser printed composite thermoelectric thick films for thermoelectric generator applications

This paper describes novel processes for preparing thermoelectric composite materials compatible with thick film dispenser printing fabrication processes. Optimization of process parameters to improve thermoelectric properties is introduced. We explore the use of n-type Bi2Te3 and p-type Sb2Te3 materials to achieve properties suitable for use in low cost high aspect ratio microscale thermoelectric generators. Printable thermoelectric inks consisted of dispersed semiconductor powders in an epoxy resin system. Thick films were printed on glass substrates and cured at temperatures ranging from 150 to 350 °C. The best achievable power factors for n-type Bi2Te3-epoxy and p-type Sb2Te3-epoxy composite films were 1.5×10−4 W/m K2 and 8.4×10−4 W/m K2, respectively. Figure of merit (ZT) values for n-type Bi2Te3-epoxy and p-type Sb2Te3-epoxy composites were 0.16 and 0.41, respectively, which are much higher than previously reported ZT values for composite thermoelectric materials.

[1]  Paul K. Wright,et al.  A MEMS AC current sensor for residential and commercial electricity end-use monitoring , 2009 .

[2]  G. Vineyard,et al.  Semiconductor Thermoelements and Thermoelectric Cooling , 1957 .

[3]  Tatsuya Shimoda,et al.  Solution-processed silicon films and transistors , 2006, Nature.

[4]  U. Dillner,et al.  Transport properties of flash-evaporated (Bi1 − xSbx)2Te3 films I: Optimization of film properties , 1990 .

[5]  D. Rowe.  Thermoelectrics Handbook , 2005 .

[6]  Kaoru Sato,et al.  The thermoelectric properties and crystallography of Bi‐Sb‐Te‐Se thin films grown by ion beam sputtering , 1993 .

[7]  M. Zakeri,et al.  Low temperature synthesis of nanocrystalline Sb2Te3 by mechanical alloying , 2008 .

[8]  Osamu Yamashita,et al.  Bismuth telluride compounds with high thermoelectric figures of merit , 2003 .

[9]  Pedro Alpuim,et al.  Thermoelectric Properties of Bi2Te3/Sb2Te3 Thin Films , 2006 .

[10]  Rama Venkatasubramanian,et al.  MOCVD of Bi2Te3, Sb2Te3 and their superlattice structures for thin-film thermoelectric applications , 1997 .

[11]  D. Ryden.  A comparison between the transport properties of single crystal, polycrystal and powder anisotropic semiconductors , 1971 .

[12]  M. Plissonnier,et al.  Development of (Bi,Sb)2(Te,Se)3-Based Thermoelectric Modules by a Screen-Printing Process , 2010 .

[13]  Peter Glynne-Jones,et al.  An investigation of self-powered systems for condition monitoring applications☆ , 2004 .

[14]  P. Detemple,et al.  Coin-size coiled-up polymer foil thermoelectric power generator for wearable electronics , 2006 .

[15]  M. Strasser,et al.  Micromachined CMOS thermoelectric generators as on-chip power supply , 2004 .

[16]  Shlomo Magdassi,et al.  Ink‐Jet Printing of Metallic Nanoparticles and Microemulsions , 2005 .

[17]  Melvin N. Miller.  Bounds for Effective Electrical, Thermal, and Magnetic Properties of Heterogeneous Materials , 1969 .

[18]  B. Legendre,et al.  Phase diagram of the ternary system GeSbTe. I. The subternary GeTeSb2Te3Te , 1984 .

[19]  Jingfeng Li,et al.  Effect of mixed grain sizes on thermoelectric performance of Bi2Te3 compound , 2009 .

[20]  Jingfeng Li,et al.  Effects of process parameters on electrical properties of n-type Bi2Te3 prepared by mechanical alloying and spark plasma sintering , 2007 .

[21]  Michel W. Barsoum,et al.  Effect of sintering temperature on the thermoelectric properties of pulse discharge sintered (Bi0.24Sb0.76)2Te3 alloy , 2005 .

[22]  Christofer Hierold,et al.  Optimization and fabrication of thick flexible polymer based micro thermoelectric generator , 2006 .

[23]  D. Cho,et al.  Effects of annealing on the thermoelectric and microstructural properties of deformed n-type Bi2Te3-based compounds , 2006 .

[24]  H J Goldsmid,et al.  The use of semiconductors in thermoelectric refrigeration , 1954 .

[25]  C. Uher,et al.  Transport coefficients of titanium-doped Sb2Te3 single crystals. , 2005 .

[26]  Otmar Pachinger,et al.  Long-term results of high vs. normal impedance ventricular leads on actual (Real-Life) pacemaker generator longevity. , 2008, Europace : European pacing, arrhythmias, and cardiac electrophysiology : journal of the working groups on cardiac pacing, arrhythmias, and cardiac cellular electrophysiology of the European Society of Cardiology.

[27]  Chung-Chih Wu,et al.  Ink-jet printing of doped polymers for organic light emitting devices , 1998 .

[28]  S. Gambini,et al.  A 52 $\mu$ W Wake-Up Receiver With $-$ 72 dBm Sensitivity Using an Uncertain-IF Architecture , 2009, IEEE Journal of Solid-State Circuits.

[29]  Daniel A. Steingart,et al.  Tailoring Electrochemical Capacitor Energy Storage Using Direct Write Dispenser Printing , 2008 .