Pulsed laser deposition of c-axis oriented aluminum nitride thin films on silicon

Results on the deposition of aluminum nitride thin films on silicon (111) substrates by pulsed laser deposition are reported. A KrF excimer laser was used to ablate in vacuum an AlN target. The intensity and the repetition rate of the laser as well as the substrate temperature were varied and their effects on film properties were determined. The AlN films were characterized by several techniques such as in situ laser interferometry, X-ray diffraction, X-ray photoelectron spectroscopy, atomic force microscopy and transmission electron microscopy. At a deposition temperature of 500 °C and a laser intensity of 1 × 10 8 W/cm 2 , highly oriented AlN layers are deposited. Increasing the laser intensity leads to the presence of metallic Al in the films. As temperature is increased from 500 to 920 °C, the growth rate is found to decrease but the crystalline structure as well as the smoothness of the films are both significantly improved. It is also found that a reduction of the growth rate by varying the repetition rate from 30 to 10 Hz leads to a further improvement of the crystalline quality of the AlN layers.

[1]  H. Okano,et al.  Preparation of c-Axis Oriented AlN Thin Films by Low-Temperature Reactive Sputtering , 1992 .

[2]  M. Khan,et al.  Influence of buffer layers on the deposition of high quality single crystal GaN over sapphire substrates , 1993 .

[3]  H. Morkoç,et al.  Large‐band‐gap SiC, III‐V nitride, and II‐VI ZnSe‐based semiconductor device technologies , 1994 .

[4]  M. Khakani,et al.  Effect of laser intensity on the microstructural and mechanical properties of pulsed laser deposited diamond-like-carbon thin films , 1999 .

[5]  R. Vispute,et al.  High quality epitaxial aluminum nitride layers on sapphire by pulsed laser deposition , 1995 .

[6]  R. Sporken,et al.  Epitaxial growth of aluminum nitride layers on Si(111) at high temperature and for different thicknesses , 1997 .

[7]  H. Morkoç,et al.  In situ transmission electron microscopy of AlN growth by nitridation of (0001) α-Al2O3 , 1998 .

[8]  Isamu Akasaki,et al.  Effects of ain buffer layer on crystallographic structure and on electrical and optical properties of GaN and Ga1−xAlxN (0 < x ≦ 0.4) films grown on sapphire substrate by MOVPE , 1989 .

[9]  Jai-Young Lee,et al.  Characteristics of hydrogenated aluminum nitride films prepared by radio frequency reactive sputtering and their application to surface acoustic wave devices , 1997 .

[10]  D. Lowndes,et al.  Electroless copper films deposited onto laser-activated aluminum nitride and alumina , 1994 .

[11]  Dispersion properties of aluminum nitride as measured by an optical waveguide technique , 1997 .

[12]  Ying-Chung Chen,et al.  Low‐temperature growth of aluminum nitride thin films on silicon by reactive radio frequency magnetron sputtering* , 1996 .

[13]  T. Venkatesan,et al.  Advances in pulsed laser deposition of nitrides and their integration with oxides , 1998 .

[14]  Jian Sun,et al.  Preparation of AlN films by pulsed laser deposition using sintered aluminum nitride and elemental aluminum as raw materials , 2001 .

[15]  R. Davis,et al.  Epitaxial growth of AlN by plasma-assisted, gas-source molecular beam epitaxy , 1993 .

[16]  Jagdish Narayan,et al.  Epitaxial growth of AlN thin films on silicon (111) substrates by pulsed laser deposition , 1995 .

[17]  George K. Wong,et al.  Optical second-harmonic generation in sputter-deposited AlN films , 1998 .