The effect of hydrophobicity in alkaline electrodes for passive DMFC

The effect of hydrophobicity in alkaline electrodes has been investigated in an effort to improve their performance in passive direct methanol fuel cells. Two approaches have been used to increase the hydrophobicity within the electrodes. One is using a more hydrophobic ionomer, and the other is introducing polytetrafluoroethylene (PTFE) into the catalyst layer. Two types of anion exchange ionomers with different hydrophobicity have been synthesized for this study. The effect of ion exchange capacity, ionic conductivity, and water uptake of the ionomers on the electrode performance has been studied using a half-cell test. The use of a hydrophobic ionomer resulted in enhanced cathode performance even though the ionic conductivity was lower than the more hydrophilic ionomer. Also, the addition of PTFE improved both the cathode and anode performance. The improved alkaline electrode performance was compared to a traditional acid electrode using Nafion as the ionomer. The performance increased threefold as a result of higher hydrophobicity in alkaline electrode.

[1]  E. Passalacqua,et al.  Influence of Nafion loading in the catalyst layer of gas-diffusion electrodes for PEFC , 1999 .

[2]  Y. Yamazaki,et al.  Influence of anion ionomer content and silver cathode catalyst on the performance of alkaline membrane electrode assemblies (MEAs) for direct methanol fuel cells (DMFCs) , 2008 .

[3]  C. Wan,et al.  Influence of PTFE dispersion in the catalyst layer of porous gas-diffusion electrodes for phosphoric acid fuel cells , 1994 .

[4]  Zhigang Qi,et al.  Open circuit voltage and methanol crossover in DMFCs , 2002 .

[5]  Christophe Coutanceau,et al.  Development of electrocatalysts for solid alkaline fuel cell (SAFC) , 2006 .

[6]  T. Osaka,et al.  Cell performance of Pd–Sn catalyst in passive direct methanol alkaline fuel cell using anion exchange membrane , 2009 .

[7]  Tianshou Zhao,et al.  Effect of polymer binders in anode catalyst layer on performance of alkaline direct ethanol fuel cells , 2009 .

[8]  Keith Scott,et al.  Development of direct methanol alkaline fuel cells using anion exchange membranes , 2004 .

[9]  K. Scott,et al.  Performance of a direct methanol alkaline membrane fuel cell , 2008 .

[10]  P. Kohl,et al.  Characterization of anion exchange ionomers in hybrid polymer electrolyte fuel cells. , 2010, ChemSusChem.

[11]  Ermete Antolini,et al.  Alkaline direct alcohol fuel cells , 2010 .

[12]  R. Slade,et al.  Alkaline anion-exchange radiation-grafted membranes for possible electrochemical application in fuel cells , 2003 .

[13]  P. Kohl,et al.  Anionic polysulfone ionomers and membranes containing fluorenyl groups for anionic fuel cells , 2009 .

[14]  Hyea Kim,et al.  Sol-gel based silica electrodes for inorganic membrane direct methanol fuel cells , 2010 .

[15]  O. Savadogo.  Comparison of Methanol Crossover among Four Types of Nafion Membranes , 2004 .

[16]  W. Vielstich,et al.  Investigation of methanol crossover and single electrode performance during PEMDMFC operation: A study using a solid polymer electrolyte membrane fuel cell system , 1998 .

[17]  Hyea Kim,et al.  Anionic-cationic bi-cell design for direct methanol fuel cell stack , 2010 .

[18]  Jamie P. Kizewski,et al.  Novel electrolyte membranes and non-Pt catalysts for low temperature fuel cells , 2010 .

[19]  K. Scott,et al.  Direct methanol alkaline fuel cells with catalysed anion exchange membrane electrodes , 2005 .

[20]  Masashi Watanabe,et al.  Design of Direct Methanol Alkaline Fuel Cell with Anion Conductive Membrane Prepared by Plasma Polymerization , 2010 .