Development of open-cathode polymer electrolyte fuel cells using printed circuit board flow-field plates: Flow geometry characterisation

Abstract Open-cathode air-breathing fuel cells have the advantage of reduced system complexity and simplified operation, as oxygen is taken directly from ambient air without the need for blowers/compressors. In this study, printed circuit boards (PCBs) are used as flow-field plates. The use of PCBs offers the potential for significant cost reduction due to their well-established manufacturing processing and low materials cost. This study investigates the effect of varying the cathode geometry (parallel and circular) and opening ratios (43%, 53% and 63%) on fuel cell performance using polarisation curves, electrochemical impedance spectroscopy (EIS) and thermal imaging. The results obtained indicate that circular openings afford lower Ohmic resistance than parallel flow-field designs, which helps improve contact between the gas diffusion layer and flow-field plate. However, flow-field plates with circular openings suffer from greater mass transport limitation effects. Likewise, greater opening ratios offer better mass transport but increased Ohmic resistance as a result of the reduced area of lands/ribs. The thermal imaging results reveal lower temperature in the middle of the fuel cell due to “bowing” of the printed circuit board flow field plates which reduces the local current density. A trade-off between these factors results in a design with a maximum area specific power density of 250 mW cm −2 .

[1]  Narissara Bussayajarn,et al.  Planar air breathing PEMFC with self-humidifying MEA and open cathode geometry design for portable applications , 2009 .

[2]  Suk Won Cha,et al.  The role of ambient conditions on the performance of a planar, air-breathing hydrogen PEM fuel cell , 2006 .

[3]  R. O’Hayre,et al.  Optimization of Passive Air Breathing Fuel Cell Cathodes , 2008 .

[4]  D. Brett,et al.  A study of the effect of water management and electrode flooding on the dimensional change of polymer electrolyte fuel cells , 2013 .

[5]  S. Asghari,et al.  Study of PEM fuel cell performance by electrochemical impedance spectroscopy , 2010 .

[6]  Suk Won Cha,et al.  Development of portable fuel cell arrays with printed-circuit technology , 2003 .

[7]  Kazuyoshi Fushinobu,et al.  Visualization of the Membrane Temperature Field of a Polymer Electrolyte Fuel Cell , 2004 .

[8]  Christopher Hebling,et al.  A PEM fuel cell for combined measurement of current and temperature distribution, and flow field flooding , 2004 .

[9]  Andreas Schmitz,et al.  Planar self-breathing fuel cells , 2003 .

[10]  P. Lund,et al.  Effect of cathode structure on planar free-breathing PEMFC , 2004 .

[11]  Fritz B. Prinz,et al.  Engineering model of a passive planar air breathing fuel cell cathode , 2007 .

[12]  P. Bouillon,et al.  Innovative water management in micro air-breathing polymer electrolyte membrane fuel cells , 2010 .

[13]  Wang Ying,et al.  Effects of cathode channel configurations on the performance of an air-breathing PEMFC , 2005 .

[14]  In-Hwan Oh,et al.  A study on cathode structure and water transport in air-breathing PEM fuel cells , 2006 .

[15]  Suk Won Cha,et al.  Air-breathing miniature planar stack using the flexible printed circuit board as a current collector , 2009 .

[16]  D. Brett,et al.  A multichannel frequency response analyser for impedance spectroscopy on power sources , 2013 .

[17]  Nigel P. Brandon,et al.  Review of Materials and Characterization Methods for Polymer Electrolyte Fuel Cell Flow-Field Plates , 2007 .

[18]  Wang Ying,et al.  Three-dimensional analysis for effect of channel configuration on the performance of a small air-breathing proton exchange membrane fuel cell (PEMFC) , 2005 .

[19]  Cody Squibb,et al.  Experimental evaluation of cell temperature effects on miniature, air-breathing PEM fuel cells , 2011 .

[20]  D. Brett,et al.  Current collector design for closed-plenum polymer electrolyte membrane fuel cells , 2014 .

[21]  Cody Squibb,et al.  Experimental Evaluation of Cell Temperature Effects on Miniature, Air-Breathing PEM Fuel Cells , 2011 .

[22]  Fritz B. Prinz,et al.  Passive water management at the cathode of a planar air-breathing proton exchange membrane fuel cell , 2010 .

[23]  Takemi Chikahisa,et al.  Effect of cathode separator structure on performance characteristics of free-breathing PEMFCs , 2006 .

[24]  M. Usman Iftikhar,et al.  Dynamic modeling of proton exchange membrane fuel cell using non-integer derivatives , 2006 .

[25]  V. Pérez-Herranz,et al.  Study of the electrochemical behaviour of a 300 W PEM fuel cell stack by Electrochemical Impedance Spectroscopy , 2014 .

[26]  In-Hwan Oh,et al.  Effects of cathode open area and relative humidity on the performance of air-breathing polymer electrolyte membrane fuel cells , 2006 .

[27]  J. Robinson,et al.  Dead-ended anode polymer electrolyte fuel cell stack operation investigated using electrochemical impedance spectroscopy, off-gas analysis and thermal imaging , 2014 .

[28]  Lateral Ionic Conduction in Planar Array Fuel Cells , 2003 .

[29]  Jenn-Jiang Hwang,et al.  Mass/electron co-transports in an air-breathing cathode of a PEM fuel cell , 2006 .

[30]  Peter Lund,et al.  Evaluation of planar free-breathing polymer electrolyte membrane fuel cell design , 2004 .

[31]  Nigel P. Brandon,et al.  Application of infrared thermal imaging to the study of pellet solid oxide fuel cells , 2007 .

[32]  Mina Hoorfar,et al.  Study of proton exchange membrane fuel cells using electrochemical impedance spectroscopy technique – A review , 2013 .

[33]  Jian Colin Sun,et al.  AC impedance technique in PEM fuel cell diagnosis—A review , 2007 .

[34]  Hang Guo,et al.  Temperature distribution on the MEA surface of a PEMFC with serpentine channel flow bed , 2006 .

[35]  Oluwamayowa A. Obeisun,et al.  Effect of temperature uncertainty on polymer electrolyte fuel cell performance , 2014 .

[36]  D. Brett,et al.  Effect of clamping pressure on ohmic resistance and compression of gas diffusion layers for polymer electrolyte fuel cells , 2012 .

[37]  Andreas Schmitz,et al.  Modeling Planar and Self-Breathing Fuel Cells for Use in Electronic Devices , 2004 .