Experimental analyses to investigate the feasibility and effectiveness in using heat-pipe embedded end-mills

This study experimentally verifies the feasibility and effectiveness of heat-pipe cooling in end-milling operations. The basic idea is to embed a heat-pipe at the center of an end-mill with the evaporator close to the tool tip, and the condenser at the tool end. Thus, most of heat generated on the end-mill tip can be quickly removed dependent on convection heat transfer by means of heat-pipe. The end-milling experiments were carried out on a CNC vertical machining center under three different cooling conditions, including dry milling, fluid cooling, and heat-pipe cooling. The work material was AISI 1040 steel, and hard alloy was chosen for the cutting tool material. Flank wear is considered as the criterion for tool failure and the wear was measured using a Hisomet II Toolmaker's microscope. The tests were conducted until the end-mill was rejected when maximum flank wear equal to 0.30 mm was recorded. The results validate that heat-pipe-assisted cooling in end-milling processes can effectively perform thermal management comparable to the fluid cooling used pervasively in the manufacturing industry, increasing the service life of the end-mill.

[1]  T. C. Daniels,et al.  Investigations of the factors affecting the performance of a rotating heat pipe , 1975 .

[2]  C. K. Toh,et al.  Comparison of chip surface temperature between up and down milling orientations in high speed rough milling of hardened steel , 2005 .

[3]  P. Phelan.  An introduction to heat pipes , 1996 .

[4]  Tien-Chien Jen,et al.  Thermal Performance of Heat Pipe Drill: Experimental Study , 2003 .

[5]  Tien-Chien Jen,et al.  Thermal Management of a Heat-Pipe Drill: A FEM Analysis , 2003 .

[6]  Mark T. North,et al.  Investigation of dry machining with embedded heat pipe cooling by finite element analysis and experiments , 2007 .

[7]  Branko Tadic,et al.  Conservative-Force-Controlled Feed Drive System for Down Milling , 2011 .

[8]  M. Elbestawi,et al.  An investigation of a heat pipe cooling system for use in turning on a lathe , 1995 .

[9]  Tien-Chien Jen,et al.  Nonlinear numerical analysis in transient cutting tool temperatures , 2003 .

[10]  Z. Pálmai.  Cutting temperature in intermittent cutting , 1987 .

[11]  M. C. Shaw.  Metal Cutting Principles , 1960 .

[12]  P. Sreejith,et al.  Dry machining: Machining of the future , 2000 .

[13]  A. Noorul Haq,et al.  Investigation of the effects of cooling in hard turning operations , 2006 .

[14]  B. Mills,et al.  The Application of Scanning Electron Microscopy to the Study of Temperatures and Temperature Distributions in M2 High Speed Steel Twist Drills , 1981 .

[15]  Anselmo Eduardo Diniz,et al.  Tool wear and tool life in end milling of 15–5 PH stainless steel under different cooling and lubrication conditions , 2009 .

[16]  A. Faghri,et al.  Two-Dimensional Rotating Heat Pipe Analysis , 1995 .

[17]  Shane Y. Hong,et al.  Improvement of Chip Breaking in Machining Low Carbon Steel by Cryogenically Precooling the Workpiece , 1998 .

[18]  S. H. Yeo,et al.  Effect of cutting fluid on the machinability of metal matrix composites , 1997 .

[19]  Lin Zhu,et al.  Investigation of Heat Pipe Cooling in Drilling Applications: Part 2—Thermal, Structural Static, and Dynamic Analyses , 2009 .

[20]  T. Ueda,et al.  An experimental technique for the measurement of temperature on CBN tool face in end milling , 2007 .

[21]  Tien-Chien Jen,et al.  Investigation of heat pipe cooling in drilling applications. Part I: preliminary numerical analysis and verification , 2002 .

[22]  John S. Agapiou,et al.  Metal Cutting Theory and Practice , 1996 .

[23]  A. Ali,et al.  Tool Temperatures in Interrupted Metal Cutting , 1992 .

[24]  Steven R Schmid Kalpakjian,et al.  Manufacturing Engineering and Technology , 1989 .

[25]  G. P. Peterson,et al.  An Introduction to Heat Pipes: Modeling, Testing, and Applications , 1994 .