A new methodology for concrete resistivity assessment using the instantaneous polarization response of its metal reinforcement framework

Abstract A new methodology is developed to assess concrete cover resistivity using the instantaneous response of the polarization of a metal rebar (galvanostatic pulse method). The instantaneous ohmic drop is linked only with the concrete resistance, which depends on the concrete cover and resistivity, and rebar diameter. A numerical model was developed in Comsol Multiphysics® in order to create a graph linking concrete resistivity to concrete resistance for concrete cover ranging between 1 and 160 mm. This graph and the measured ohmic drop can be used to determine concrete resistivity for any rebar diameter/concrete cover configuration. The theory developed numerically was then confirmed using an experimental setup with controlled water resistivity. The theory is then generalized for counter electrode (CE) diameter ranging from 20 to 70 mm. Finally, the study reveals that the graph developed for a single rebar can be used for any rebar framework density.

[1]  C. Andrade,et al.  A new method forin-situ measurement of electrical resistivity of reinforced concrete , 1996 .

[2]  Bernhard Elsener,et al.  Corrosion rate of steel in concrete: evaluation of confinement techniques for on-site corrosion rate measurements , 2009 .

[3]  M. Raupach,et al.  Determination of the distribution of electrical resistivity in reinforced concrete structures using electrical resistivity tomography , 2015 .

[4]  J. Newman.  Resistance for Flow of Current to a Disk , 1966 .

[5]  Jean-Paul Balayssac,et al.  Proposal for an alternative operative method for determination of polarisation resistance for the quantitative evaluation of corrosion of reinforcing steel in concrete cooling towers , 2015 .

[6]  J. Sykes,et al.  A GALVANOSTATIC PULSE TECHNIQUE FOR INVESTIGATION OF STEEL CORROSION IN CONCRETE , 1989 .

[7]  S. Laurens,et al.  Steady-state polarization response of chloride-induced macrocell corrosion systems in steel reinforced concrete — numerical and experimental investigations , 2016 .

[8]  Javier Sánchez,et al.  Determination of reinforced concrete durability with on-site resistivity measurements , 2017 .

[9]  C. Alonso,et al.  Test methods for on-site corrosion rate measurement of steel reinforcement in concrete by means of the polarization resistance method , 2004 .

[10]  J. M. Miranda,et al.  Considerations on reproducibility of potential and corrosion rate measurements in reinforced concrete , 2004 .

[11]  M. Geiker,et al.  Non-destructive elecrochemical monitoring of reinforcement corrosion , 2009 .

[12]  Javier Sánchez,et al.  Modification of four point method to measure the concrete electrical resistivity in presence of reinforcing bars , 2014 .

[13]  Erik J. Sellevold,et al.  Electrical resistivity of concrete , 1995 .

[14]  M. Raupach,et al.  Numerical modelling of corrosion – Theoretical backgrounds – , 2006 .

[15]  F. Wenner.  A method for measuring earth resistivity , 1915 .

[16]  Carmen Andrade,et al.  On-site measurements of corrosion rate of reinforcements , 2001 .

[17]  Fabrice Deby,et al.  Significance of macrocell corrosion of reinforcing steel in partially carbonated concrete: numerical and experimental investigation , 2015 .

[18]  M. Vazquez,et al.  Corrosion of reinforcing steel evaluated by means of concrete resistivity measurements , 2002 .

[19]  W. McCarter,et al.  Two-point concrete resistivity measurements: interfacial phenomena at the electrode–concrete contact zone , 2015 .

[20]  Mette Rica Geiker,et al.  Measuring the corrosion rate of steel in concrete – effect of measurement technique, polarisation time and current , 2012 .

[21]  O. Sengul,et al.  Effect of cement type on the resistance of concrete against chloride penetration , 2011 .

[22]  Rob B. Polder,et al.  Test methods for on site measurement of resistivity of concrete — a RILEM TC-154 technical recommendation , 2001 .

[23]  Y. Ballim,et al.  A framework for use of durability indexes in performance-based design and specifications for reinforced concrete structures , 2008 .

[24]  J. M. Miranda,et al.  Possibilities and problems of in situ techniques for measuring steel corrosion rates in large reinforced concrete structures , 2005 .

[25]  Francisco Presuel-Moreno,et al.  Numerical modeling of the effects of rebar presence and/or multilayered concrete resistivity on the apparent resistivity measured via the Wenner method , 2013 .

[26]  Pouria Ghods,et al.  Numerical investigation of the role of embedded reinforcement mesh on electrical resistivity measurements of concrete using the Wenner probe technique , 2016 .

[27]  U. Angst,et al.  On the applicability of the Stern–Geary relationship to determine instantaneous corrosion rates in macro‐cell corrosion , 2015 .