Novel approach to proper design of combustion and radiant chambers

Abstract Combustion and radiant chambers with inbuilt heat transfer surfaces are integral parts of a wide range of process and power equipment such as fired heaters, power boilers, or incinerator furnaces. Operating problems that many of these combustion chambers suffer from are typically due to the design procedures using data of insufficient accuracy regarding the calculated local heat transfer data in individual parts of the chambers equipped with modern low-NO x burners. These problems, obviously, force the designers to devise more accurate design procedures for the respective equipment. The paper therefore discusses the main results obtained so far in the course of a several years long research effort and presents a basic outline of an up-to-date, novel approach to proper design of combustion and radiant chambers with inbuilt heat transfer surfaces. The three most important and – considering the current design practice – also original components of the presented novel approach which significantly improve the quality of the resulting combustion chamber designs are (i) experimental determination of the actual burner heat flux distribution, (ii) determination of the actual fuel burnout profile of the burner from the obtained heat flux profile using the validated MPF model, and (iii) utilisation of the respective fuel burnout profile in the course of design of the combustion chamber and its inbuilt heat transfer surfaces together with calculation of the local heat flux distribution via the plug-flow-based method, thus replacing the currently used design methods based on the “well stirred” models.

[1]  Z. Jegla,et al.  Optimum Arrangement of Tube Coil in Radiation Type of Tubular Furnace , 2008 .

[2]  Peng Yen Liew,et al.  Numerical Analysis of Heat Transfer in Radiant Section of Fired Heater with Realistic Imperfect Geometry of Tube Coil , 2014 .

[3]  G. R. Martin.  Heat-flux imbalances in fired heaters cause operating problems , 1998 .

[4]  J. Hajek,et al.  Standards for fired heater design: An assessment based on computational modelling , 2015 .

[5]  Raymond Viskanta,et al.  Heat transfer in steam boiler furnaces , 1988 .

[6]  Dawid Taler,et al.  Identification of local heat flux to membrane water-walls in steam boilers , 2009 .

[7]  Z. Jegla,et al.  The Conceptual Design of a Radiant Chamber and Preliminary Optimization of a Process Tubular Furnace , 2006 .

[8]  R. G. Pelini.  Heat flux And film Temperature In Fired, Thermal-Fluid Heaters , 2008 .

[9]  G. L. Shires,et al.  Process Heat Transfer , 1994 .

[10]  Charles Baukal,et al.  The John Zink Hamworthy combustion handbook , 2013 .

[11]  Ryszard A. Białecki,et al.  Numerical simulations of the industrial circulating fluidized bed boiler under air- and oxy-fuel combustion , 2015 .

[12]  Petr Stehlík,et al.  Secondary Combustion Chamber with Inbuilt Heat Transfer Area – Thermal Model for Improved Waste-to-energy Systems Modelling , 2010 .

[13]  P. Bělohradský,et al.  Biodiesel (EN 14213) heating oil substitution potential for petroleum based light heating oil in a 1 MW stationary combustion facility. , 2013 .

[14]  Santanu Bandyopadhyay,et al.  Fired heater integration into total site and multiple fired heater targeting , 2012 .

[15]  Hari B. Vuthaluru,et al.  CFD based prediction of erosion rate in large scale wall-fired boiler , 2012 .

[16]  Ali Jamali,et al.  Crude oil direct fired furnace model , 2015 .

[17]  Xu Zhou,et al.  Thermal-hydraulic analysis of a 600 MW supercritical CFB boiler with low mass flux , 2012 .

[18]  Dawid Taler,et al.  Identification of thermal boundary conditions in heat exchangers of fluidized bed boilers , 2013 .

[19]  Santanu Bandyopadhyay,et al.  Improved area—energy targeting for fired heater integrated heat exchanger networks , 2012 .

[20]  G. T. Polley,et al.  Modeling the thermo-hydraulic performance of direct fired heaters for crude processing , 2012 .

[21]  Sergio Mussati,et al.  Mixed Integer Nonlinear Programming model for the optimal design of fired heaters , 2009 .

[22]  Stanley M. Walas,et al.  Chemical Process Equipment : Selection and Design , 1988 .

[23]  Z. Jegla.  Development of Modified Plug-flow Furnace Model for Identification of Burner Thermal Behavior , 2013 .

[24]  Sadik Kakaç,et al.  Boilers, evaporators, and condensers , 1991 .

[25]  Qinhui Wang,et al.  Heat flux determination based on the waterwall and gas–solid flow in a supercritical CFB boiler , 2016 .

[26]  Martín Picón-Núñez,et al.  Analysis of the influence of operating conditions on fouling rates in fired heaters , 2014 .

[27]  Alireza Bahadori,et al.  Novel predictive tools for design of radiant and convective sections of direct fired heaters , 2010 .

[28]  Z. Jegla,et al.  Validation of Developed Modified Plug-flow Furnace Model for Identification of Burner Thermal Behaviour , 2015 .

[29]  S. Izadpanah,et al.  A numerical study on thermal behavior of a D-type water-cooled steam boiler , 2012 .

[30]  E. M. Matos,et al.  Predicting coke formation due to thermal cracking inside tubes of petrochemical fired heaters using a fast CFD formulation , 2006 .

[31]  J. Ward,et al.  Identifying and quantifying energy savings on fired plant using low cost modelling techniques , 2012 .