Micro-EHL Analysis of Ground and Superfinished Steel Discs Used to Simulate Gear Tooth Contacts

This paper describes the results of a full micro-elastohydrodynamic lubrication (micro-EHL) analysis of steel discs. The first aim of the work was to compare the theoretical contact pressures and film thickness values for two significantly different types of surface finish. The first surface type was that of conventionally ground steel discs of a roughness value (Ra) of about 0.4 μm in which the direction of finish was transverse to that of lubricant entrainment. The second surface was that of a superfinished steel disc which had an Ra value of less than 0.1 μm. This comparison showed that, although the smoother surfaces gave a lower magnitude of pressure rippling in the contact than was the case with the rough surfaces, the minimum film thickness values were almost the same. A second aim of the work was to compare the contact pressure distribution under lubricated conditions with that obtained from dry contact simulation at the same load. It was found that the dry contact pressure provided a good approxi...

[1]  R. Bosma,et al.  The Influence of Longitudinal and Transverse Roughness on the Elastohydrodynamic Lubrication of Circular Contacts , 1988 .

[2]  L. Chang.  Traction in thermal elastohydrodynamic lubrication of rough surfaces , 1992 .

[3]  Henry Peredur Evans,et al.  A Model for Elastohydrodynamic Film Failure in Contacts Between Rough Surfaces Having Transverse Finish , 1996 .

[4]  R W Snidle,et al.  A Simple Method of Elastic Contact Simulation , 1994 .

[5]  Henry Peredur Evans,et al.  Conditions for Scuffing Failure of Ground and Superfinished Steel Disks at High Sliding Speeds Using a Gas Turbine Engine Oil , 1995 .

[6]  A. Jackson,et al.  On the Pressure Rippling and Roughness Deformation in Elastohydrodynamic Lubrication of Rough Surfaces , 1993 .

[7]  H. P. Evans,et al.  The elastohydrodynamic lubrication of point contacts at heavy loads , 1982, Proceedings of the Royal Society of London. A. Mathematical and Physical Sciences.

[8]  R W Snidle,et al.  Elastohydrodynamic Lubrication of Heavily Loaded Circular Contacts , 1989 .

[9]  T. F. Conry,et al.  The Effects of Surface Irregularities on the Elastohydrodynamic Lubrication of Sliding Line Contacts. Part I—Single Irregularities , 1984 .

[10]  M. N. Webster,et al.  A Study of Elastohydrodynamic Lubrication of Rough Surfaces , 1991 .

[11]  Henry Peredur Evans,et al.  Micro-Elastohydrodynamic Lubrication of an Elliptical Contact With Transverse and Three-Dimensional Sinusoidal Roughness , 1989 .

[12]  A. A. Elsharkawy,et al.  Subsurface Stresses in Micro-EHL Line Contacts , 1991 .

[13]  Farshid Sadeghi.  A Comparison of the Fluid Models Effect on the Internal Stresses of Rough Surfaces , 1991 .

[14]  Henry Peredur Evans,et al.  Simulation of Elastohydrodynamic Contacts Between Rough Surfaces , 1992 .

[15]  Liming Chang,et al.  Fundamental Differences Between Newtonian and Non-Newtonian Micro-EHL Results , 1995 .

[16]  T. F. Conry,et al.  The effects of surface irregularities on the elastohydrodynamic lubrication of sliding line contacts. I. Single irregularities. II. Wavy surfaces , 1984 .

[17]  W. E. ten Napel,et al.  Surface roughness effects in an EHL line contact , 1992 .